TK-30874 Requesting [ANH Stunt] EIB Status (AP)

[0megaRed[TK]]

Hi team!
Sending in my EIB application with my ANH Stunt suit from AP (AuthenticProps).

 

Trooper Information

    Name :  Eric Poirier
    FISD Forum Name :  0megaRed
    Legion ID :  30874
    Garrison :  Garnison Forteresse Impériale
    Height :   5'8"
    Weight :  157lb

    501st link : https://www.501st.com/members/displaymemberdetails.php?userID=39928

Costume Information

    Armor Maker :  AP
    Helmet Maker :  AP

    Gloves and ANH Stunt Hand Guards :  AP
    Neck Seal :  DarmansProps
    Soft Belt :  AP
    Boots :  KeepTrooping
    Holster :  AP
    Fans :  Henry's Helmet Fans
    Blaster :  Unknown

_________________________
 

[Tall_Trooper[TK]]

Nice looking TK! Maybe you can put a little abs paste in the small gap.

 

 

 

Like this

 

Good Luck

[0megaRed[TK]]

Thanks for the heads up!
that's something I never thought of doing, should I wait 'till the app team mentions it? Would it pass EIB status 'as is'?

 

I do plan on going to Centurion level so it will be done!

[gmrhodes13[Staff]]

1 hour ago, 0megaRed said:

Thanks for the heads up!
that's something I never thought of doing, should I wait 'till the app team mentions it? Would it pass EIB status 'as is'?

 

I do plan on going to Centurion level so it will be done!

If you have a look at other EIB applications you may notice it has been asked as a L3 Centurion requirement  

Here's just one 

Centurion Requirements:

A bit of filler in the gaps on the bottom of the thigh joint in the back will need to be applied.  This can be done with ABS paste or Sugru.

CRL L3: Lower thigh ridge joins (front and rear) shall butt-up flush against each other. Any gaps must be backed with ABS or filled as not to be noticeable.

 

                                                                                                                References

        

 

You should be fine for EIB 

 

You may want to just take out the extra material in the corners of your forearms  

 

 

Also add a little white paint to the rim of your hovi's 

• Correct Aerators/Hovi-MIX tips are present. Screens used shall be of a wide type mesh, with the rim of the mic and the inside white or painted white.

     

 

              

 

[gmrhodes13[Staff]]

There are a couple of other things you may want to address, note these are suggestions and you are welcome to disregard and wait for the DO's review, but if you have time wouldn't hurt to address some.

 

Your arms are touching in several places, I would try to bring your biceps up (they are quite low), giving you more room at the elbows. 

Shoulder elastic around bicep looks loose (rear photo)

Your shins at not at the same height on the boots, adding some velcro or elastic inside can help keep them down. 

Belt could come up a bit: 

• The top of the ABS ammo belt should sit at or just above the bottom of the central and vertical abdomen button panels.

Your belt is slightly on an angle

Trim the sharp corners off the tops of the thigh coverstrips or they will dig in you when moving

 

If your stickers aren't too old you could add some tape, pry them off carefully and replace a pencil width from the cheek

• Ideally, the tube stripes are positioned approximately a pencil width from the side of the cheek.

 

Ab and kidney look to be overlapping

      

Drop boxes should align with the end of the plastic belt

For Level 3, Drop boxes are vertically aligned with the end of the ammo belt with minimal gap between belt and box.

 

         

Detonator could come down a little 

     

Hand plates do not look like they are affixed to the gloves, could be in wrong position

     

 

Looks like you have velcro under your rear shoulder straps, these should free float.

Arms touching

Overlap side AB/Kidney

Posterior touching thighs

Loose shoulder bell elastic

 

Using a contrasting background is best when taking your photos, especially for those like your GWL (garrison web liaison) or FISD honor gallery editor  

 

Once again these are suggestions, you are welcome to wait until you hear from the Deployment Team 

 

Good luck with your application 

[0megaRed[TK]]

thank you gmrhodes13 for taking the time to 'dissect' my armor and fitment!
this is exactly what I needed to focus on specific parts to get my suit on to the next level!