SwedishTX Posted September 2 Author Report Posted September 2 3 hours ago, Nairy said: Looking forward to seeing things come together! Do you think that it will be finished this year? Would be a stretch getting it done for Comic Con 2024 in November but you can always dream, right? unfortunately not this year :/ , i must save some money for the suit and kama Quote
SwedishTX Posted October 8 Author Report Posted October 8 quick update! I have to put pause on this project for a while. i will be back! 1 Quote
Sly11[Admin] Posted October 10 Report Posted October 10 We will be here on your return. Hope all is ok. 1 Quote
SwedishTX Posted October 20 Author Report Posted October 20 (edited) yeah nothing serious but i have a question about the gold details, everything have to be "same" gold? like the face have a darker tone of gold and cracks has a brighter, it must have same? Edited October 20 by SwedishTX Quote
Sly11[Admin] Posted October 20 Report Posted October 20 I think it could be due the amount of gold on the faceplate, compared to the small amount in the cracks. Also the weathering can change how the light catches and reflects it. A combination of gold leaf and paint was used to fix up areas due to wear or damage on the Night Troopers, I would wager the same happened with Enoch in some areas. We believe it is probably supposed to look the same. 1 Quote
SwedishTX Posted November 5 Author Report Posted November 5 Hello there! done some work on Enoch and i have forgot to update here :S only thing i have problem with when i glue golden leaf is there is brush strokes, even when i use a sponge ( see shoulder ) any suggestions for something better ? 1 Quote
gmrhodes13[Staff] Posted November 5 Report Posted November 5 Depends how you applied the glue too, I was thinking of using a spray glue so there is a flat base and then a very soft round brush to dab the surface and not brush, perhaps a makeup brush. 1 Quote
Nairy[Staff] Posted November 5 Report Posted November 5 7 minutes ago, SwedishTX said: Hello there! done some work on Enoch and i have forgot to update here :S only thing i have problem with when i glue golden leaf is there is brush strokes, even when i use a sponge ( see shoulder ) any suggestions for something better ? How smooth was your shoulder sanded before? Looking good though so far! Nice work overall and the helmet is looking really cool! 1 Quote
SwedishTX Posted November 5 Author Report Posted November 5 7 minutes ago, gmrhodes13 said: Depends how you applied the glue too, I was thinking of using a spray glue so there is a flat base and then a very soft round brush to dab the surface and not brush, perhaps a makeup brush. i used a sponge to apply the glue, maybe i was to heavy on my hand i must try a makeup brush or a very fine fan brush 1 Quote
SwedishTX Posted November 5 Author Report Posted November 5 3 minutes ago, Nairy said: How smooth was your shoulder sanded before? Looking good though so far! Nice work overall and the helmet is looking really cool! i wet sand it with 800 grid, i have to try something else. Like gmrhodes said, something smoother like a makeup brush thank you man 2 Quote
SwedishTX Posted November 7 Author Report Posted November 7 Tried the makeup sponge today, work so much better! 1 Quote
gmrhodes13[Staff] Posted November 7 Report Posted November 7 50 minutes ago, SwedishTX said: Tried the makeup sponge today, work so much better! Quote
themaninthesuitcase[Admin] Posted November 8 Report Posted November 8 Lookimng good there trooper. Excited to see some of these getting done. 1 Quote
SwedishTX Posted November 12 Author Report Posted November 12 On 11/9/2024 at 12:55 AM, themaninthesuitcase said: Lookimng good there trooper. Excited to see some of these getting done. Thank you 🤘 My printer is on 24/7 now 👌 Quote
SwedishTX Posted November 12 Author Report Posted November 12 question time! Best way to secure and lock shin armor, is it elastic straps and velcro? I cant glue them together 😅 Question nr 2. shoulder straps. Does it have to be ABS plastic or is it ok to cast them in rubber/silicone? Quote
gmrhodes13[Staff] Posted November 12 Report Posted November 12 You could add elastic across the front so they can still open/close. On the rear something similar to standard TK's perhaps 1 Quote
SwedishTX Posted November 16 Author Report Posted November 16 On 11/12/2024 at 10:15 PM, gmrhodes13 said: You could add elastic across the front so they can still open/close. On the rear something similar to standard TK's perhaps unfortunately, it didn´t work :/ The files i got have that strip next to the cut Quote
Nairy[Staff] Posted November 16 Report Posted November 16 5 hours ago, SwedishTX said: unfortunately, it didn´t work :/ The files i got have that strip next to the cut You could add a strip on the inside of the side that doesn't have the strip attached to it! Just put velcro under the strip and some velcro on the strip you added! Do you think that could work? Quote
Nairy[Staff] Posted November 16 Report Posted November 16 Bad image but I think you know what I mean 2 Quote
SwedishTX Posted November 16 Author Report Posted November 16 1 hour ago, Nairy said: Bad image but I think you know what I mean yeah i tried that to when i did it there was a gap like 3-4 mm and you can see velcro. i just got home from hardware store with some stuff i must try 1 Quote
Nairy[Staff] Posted November 16 Report Posted November 16 6 minutes ago, SwedishTX said: yeah i tried that to when i did it there was a gap like 3-4 mm and you can see velcro. i just got home from hardware store with some stuff i must try This sounds weird but I'll just say it anyways to have it said: Shouldn't the print close up exactly where the cut next to the big strip is? Quote
SwedishTX Posted November 16 Author Report Posted November 16 (edited) 2 hours ago, Nairy said: This sounds weird but I'll just say it anyways to have it said: Shouldn't the print close up exactly where the cut next to the big strip is? i hear what you saying! but the cut should be under the big strip so you can close it propely, ( i use shadow armor as a reference ) this is the right way, yes? and here is how they made the cut on enoch, maybe glue a plastic strip on the inside with velcro should do the trick. i have seen other prints there the big strip is overlap the other piece Edited November 16 by SwedishTX add text Quote
Nairy[Staff] Posted November 16 Report Posted November 16 32 minutes ago, SwedishTX said: i hear what you saying! but the cut should be under the big strip so you can close it propely, ( i use shadow armor as a reference ) this is the right way, yes? and here is how they made the cut on enoch, maybe glue a plastic strip on the inside with velcro should do the trick. Would this work? I drew it like it's seen from above Plate Velcro strip Direction The blue arrow would indicate that it could go flush with the left side! Some velcro strip on the backside of the printed seam on the left (which it looks like you have already?) If you are able to bend it a bit it should be able to close up! If you don't want to have a strip going all the way along the right side then maybe a small portion in the top and one in the bottom (where it is the most bendable) 1 Quote
SwedishTX Posted November 17 Author Report Posted November 17 Update! Me and Nairy had a chat yesterday on messenger about the locking mechanism and we came up with a solution. Take a plastic strip about 50 mm wide and and 200mm long, glue one half on the armor and put velcro on the other half and tadaaa! i hope this help someone else who have same problem Thanks Nairy Put them on for a test and they fit like a glove! and i started to print Thigh armor yesterday and i´m out of filament now. Size feels right but i must wait and see when the back side is complete 2 Quote
themaninthesuitcase[Admin] Posted November 17 Report Posted November 17 Looks like a good fit, but would be nice to see a photo with a bit more context. Good work. 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.