Jump to content

paradoxb3 requesting basic pre-approval OT TK ANH Stunt (AM 4.5)


Recommended Posts

Name:  Devin Padgett
Future Garrison:  Georgia Garrison (USA)
Armor Maker:  AM 4.5
Helmet Aaker:  AM 4.5
Cloth Belt:  Imperial Issue
Neck Seal:  Trooper Bay

Holster: Trooper Bay
Boot Maker:  Crowprops
Blaster:  (none presently)
Height: 6' 0"
Weight: 215 lbs
Type: ANH Stunt

 

I've not been very active at all on my build thread for my own personal reasons, however that doesn't mean I haven't been active on my construction process.  I submit for your pre-approval review my ANH Stunt OT TK!

 

Front:
 

OJLEX4J.jpg

 

Back:

 

ZRhwmIq.jpg

 

Left:

 

HdlhSP9.jpg

 

Right:

 

VpaThxB.jpg

 

Helmet Front:

EA7825T.jpg

 

Helmet Left:

 

g5P7RvU.jpg

 

Helmet Right:

 

eOdawB1.jpg

 

Helmet Back:

 

MlM6Lbc.jpg

 

Helmet Lens Color:

8cO8ww0.jpg

 

Hetlmet S-Trim:

 

RYrY8TS.jpg

 

Ab Detail:

JtCJ7cG.jpg

 

TD:

 

2J6Dp5K.jpg

 

Shoulders:

BGHTdL2.jpg

 

Right "Han snap":

 

AZajPwg.jpg

 

Left Rivets:

 

eCIGySg.jpg

5rmCFLr.jpg

 

Rubber Gloves:

 

uCk306Q.jpg

 

Hand Guard Flex:

 

XONJElG.jpg

 

Right Thigh:

 

b2vvu1p.jpg

 

YJun6if.jpg

 

VqAJoQA.jpg

 

 

Thanks!

 

-Devin

 

  • Like 1
Link to comment
Share on other sites

Nice work, just a couple of things, you could bring your belt up at the back as it is angling down.

RbsbERB.jpg.e78181c8e4203bba1fe40f95a893031d.jpg

 

You could remove the excess clip material sticking out under your belt.

eXtIssr.jpg.0d5749e09f49f4f5883cb8c63b0082a4.jpgENBGgGW.jpg.e51da097807d11e604929621ed1556a5.jpg

 

I would also add some foam behind your sniper plate to hopefully push it forward away from your knee, it could catch on your thigh.

 

Good luck with approval

  • Like 1
Link to comment
Share on other sites

Looking SHARP, Devin.... you should have no issues getting Basic approval.   Once you get your blaster, I hope to see this set of AM armor submitted for Expert Infantry level!  ;)

  • Like 1
Link to comment
Share on other sites

Looking SHARP, Devin.... you should have no issues getting Basic approval.   Once you get your blaster, I hope to see this set of AM armor submitted for Expert Infantry level!  
Thanks! I certainly plan on it in the near future.

Sent from my SM-G975U using Tapatalk

Link to comment
Share on other sites

Nice work, just a couple of things, you could bring your belt up at the back as it is angling down.
RbsbERB.jpg.e78181c8e4203bba1fe40f95a893031d.jpg
 
You could remove the excess clip material sticking out under your belt.
eXtIssr.jpg.0d5749e09f49f4f5883cb8c63b0082a4.jpgENBGgGW.jpg.e51da097807d11e604929621ed1556a5.jpg
 
I would also add some foam behind your sniper plate to hopefully push it forward away from your knee, it could catch on your thigh.
 
Good luck with approval
That will definitely be on my to-do list. I was afraid my belt might have been sitting low. I was walking that fine line between getting everything perfect and not annoying my SO photographer. Hah

Sent from my SM-G975U using Tapatalk

  • Like 1
Link to comment
Share on other sites

Looking sharp, Devin! It's been a pleasure providing feedback outside of FISD, and Christine should have you approved in no time!
Yes and thank you very much for your help and input. Your vast knowledge and resources were invaluable and made this first build so much easier! I look forward to trooping alongside you in the not too distant future.

Sent from my SM-G975U using Tapatalk

Link to comment
Share on other sites

Approved!  TK-47501 Checking in!

 

gmrhodes13 was correct in that my TD clips needed to be shortened, but that was the only correction that was requested.  A quick snip snip and sand and I was done.

 

I want to thank everyone here for your time, your experience, your knowledge, and your invaluable input.  I couldn't have got this far without you.

 

"If I have seen further, it is by standing upon the shoulders of giants." - Sir Isaac Newton

  • Like 5
Link to comment
Share on other sites

7 hours ago, paradoxb3 said:

Approved!  TK-47501 Checking in!

 

gmrhodes13 was correct in that my TD clips needed to be shortened, but that was the only correction that was requested.  A quick snip snip and sand and I was done.

Congratulations trooper and welcome to the ranks, look forward to seeing you at EIB ;) 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...