TrooperTori[TK] Posted December 13, 2020 Report Posted December 13, 2020 Armor = Walts Trooper Factory Helmet Maker = Me? (was a part of the Kit from Walt) Blaster= Shear Tech Height = 5' 10" Boots = Imperial Boots Canvas belt = Tkittle Neck Seal = Geeky Pinks Phantastic Gaskets Holster = Darmans Props 1 Quote
gmrhodes13[Staff] Posted December 13, 2020 Report Posted December 13, 2020 Nice work trooper, there are a few suggestions you could address before the DO's get here. You will need to swap the holster to the other side for ESB Sniper plate is under your thigh, you may want to add some foam behind the shin so it pushes away from the thigh. Could you post close up photos of your thigh fronts, cover strips look a little off but can't quite see because of the low resolution of your photos. Belt should sit just under or touching the lower ab button Your left bicep has dropped below your shoulder bell. You have a gap between the backplate and kidney on the sides. Shoulder straps should be centered at the backplate. It's a little hard to see from your images as they are a bit small and not a great resolution but just checking your the back of your shins should close outside over inside so the opening isn't seen from the outside. Also a large gap between your right bicep and elbow. Should bells should have the same gaps on each side. You may also want to add some scrap ABS plastic behind the gaps in the bottom of your thighs. There shouldn't be a gap between the brackets and the end caps on your detonator. The right end cap has been trimmed a little rough. You may also want to check the length. Corners of your plastic belt are too large, they should be cut to meet the width of the belt. You also have a gap between the kidney and the butt plate which with need to be closed. Belt boxes have to align with the end of the plastic belt section. There is also quite a lot of excess material left on the sides of the chest and back plates. Appears you may have your side rivets in the wrong positions Helmet brow trim is not straight and you should see some white between the eyes and brow trim. Ears are very thick on the top sections. Hovi tips should have a white rim. Vocoder paint is a little wobbly in places. Also appears your hovi mesh may be a little bit small Right ear is a little too far forward on the base, should be angled backwards Ear has quite a large gap all the way around and the top section of the ear is quite thick, normally a small gap on the lower section is allowable but not the top of the ear You could move your shoulder straps a little further down on the chest, looks like you just have the large tab and one small attached, ideal is 1 larger tab and 4 to 5 smaller tabs There are quite a lot of photos you are missing you may want to check this list as well as other EIB applications Some photos required Close up of both sides and inside connectors of your thigh ammo strip Close up of the rear of the shins Close up of the sniper plate, front and both sides Close up of the blaster D ring Close up of your ab/kidney side rivets Close up of ab "Han" snap (top right corner) Close up of cod rivet. Close up of butt snaps Close up of your ab buttons Close up of your boots Close up of the S trim around the base of your helmet Close up of your ear screws, top and bottom Interior strapping Good luck with approval 1 Quote
husky68[TK] Posted December 13, 2020 Report Posted December 13, 2020 If making changes to the TD, you might want to rotate it so the panel is facing out. I had to make a similar change to mine. Sent from my iPhone using Tapatalk 1 Quote
justjoseph63[Staff] Posted December 13, 2020 Report Posted December 13, 2020 Hi Victoria, and thanks for your submission! As Glen mentioned, we need the photos he listed as well as a few more things before we can get started. 1. Close-up photo of the frown. 2. Close-up photo of the tube stripes. 3. Interior strapping pics, especially the side ab/kidney and back/kidney/posterior plate connections. 4. Close-up photo(s) of hand plates/gloves and how they are connected. 5. Close-up of thigh ammo pack/connection (both sides). As per the CRL for Expert Infantry level: The frown mesh must be of the wide type and the rims painted white. Holster is worn on the right side. Thanks, and we look forward to seeing the photos! Quote
TrooperTori[TK] Posted December 13, 2020 Author Report Posted December 13, 2020 (edited) 12 hours ago, husky68 said: If making changes to the TD, you might want to rotate it so the panel is facing out. I had to make a similar change to mine. Sent from my iPhone using Tapatalk What panel?? Sorry I'm unsure what you mean by TD. oh you meant the detonator omg sorry i didn't have coffee earlier now i get it it might be the picture but i do have spared endcaps will see if those are better also they may not be fuloly pushed on i wasnt sure about the no gap some pictures were a bit either or when i was looking at others Edited December 13, 2020 by TrooperTori adding stuff Quote
TrooperTori[TK] Posted December 13, 2020 Author Report Posted December 13, 2020 5 hours ago, justjoseph63 said: Hi Victoria, and thanks for your submission! As Glen mentioned, we need the photos he listed as well as a few more things before we can get started. 1. Close-up photo of the frown. 2. Close-up photo of the tube stripes. 3. Interior strapping pics, especially the side ab/kidney and back/kidney/posterior plate connections. 4. Close-up photo(s) of hand plates/gloves and how they are connected. 5. Close-up of thigh ammo pack/connection (both sides). As per the CRL for Expert Infantry level: The frown mesh must be of the wide type and the rims painted white. Holster is worn on the right side. Thanks, and we look forward to seeing the photos! I will get those up soon sorry I looked at the pin post on the top and did not realize it was outdated for the list and I can't believe i put my holster on the wrong side that is my bad it will take awhile for me to work on some of the improvements mentioned I will have to write them all down and get cracking the helmet will not be fun...... Quote
justjoseph63[Staff] Posted December 13, 2020 Report Posted December 13, 2020 We are here to help with anything you need, Victoria. You can post up any questions here or in a new thread and we can go from there! 1 Quote
gmrhodes13[Staff] Posted December 13, 2020 Report Posted December 13, 2020 4 hours ago, TrooperTori said: What panel?? Sorry I'm unsure what you mean by TD. oh you meant the detonator omg sorry i didn't have coffee earlier now i get it it might be the picture but i do have spared endcaps will see if those are better also they may not be fuloly pushed on i wasnt sure about the no gap some pictures were a bit either or when i was looking at others TD = Thermal Detonator Should be rotated downwards so more of the panel can be seen 1 Quote
illusionz_09[TK] Posted February 3, 2021 Report Posted February 3, 2021 Looks like everything has been mentioned. I know it is quite a list, but im sure with a little effort you can easily knock out that list. As far as the ears, it looks (and it may just be the picture) as if both of the ears are "right." Please confirm. Sometimes some manufactures provide 2 sets of each ears (as practice/backup) and you may have installed both rights. Please confirm. That way it fits properly. Good Luck on your updates/submission. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.