TK-18034 requesting ANH stunt EIB status (RWA) (994)

**Freddybear[TK]** · August 29, 2020

Name: Dave Fredericks
501st ID #: 18034
FISD Username: Freddybear
Garrison: United Kingdom
Legion profile: https://www.501st.com/members/displaymemberdetails.php?userID=24942
Armor: RWA Creations
Helmet: RWA Creations
Blaster: Doopy Doos with heavy modifications
Boots: Imperial Warfighters
Canvas Belt: RWA Creations
Hand Plates: Silicone
Neck seal: RWA Creations
Holster: RWA Creations
Electronics: Troopacoola dual fan system with Anker battery.
Recently cleared basic with the following submission pics:

Gloves: Rubber with silicone hand guards

Neck Seal:

Two piece Under Armor body suit with balaclava:

Boots:

Helmet:

Thermal Detonator with flathead screws painted black:

Belt:

Wrists no return edge:

Ammo thigh capped rivets painted white:

Sniper knee:

Han snap:

Left side split rivets painted white:

Cod brass rivet and butt snaps:

Ab buttons:

Shoulder bridges front and back:

E11 Blaster with M38 scope, metal screws, original counter inners, aluminum trigger guard, movable ARS switch, magnetised ammo clip, working locking pin and removable end cap:

**TKSpartan[Staff]** · August 30, 2020

Hi Dave, thanks for you EIB application.

Mean while one D.O is assigned for your review. Could you please ad a close photo of your thigh ammo pack inner side (to see the rivets type), right and left .?

Cheers :salute:

**CableGuy[TK]** · August 30, 2020

Looking great, Dave. You got this! :-)

**Freddybear[TK]** · August 30, 2020

Internal pics of Thigh ammo pack single capped rivets as requested:

**TKSpartan[Staff]** · August 30, 2020

Hi Dave, so fast response, thanks.

I'll be with you shortly. :salute:

**TKSpartan[Staff]** · September 1, 2020

Hi Dave.

in order to proceed with your application, we need you to make an small adjustment to your helmet's teeth area. There's a bit excess of paint tht needs to be removed.

CRL for basic states: Frown is painted gray and does not leave the teeth area.

WkXG5ly.jpg?2

Reference Images

Five minutes with a toothpick or cotton swab with mineral spirit or paint remover (Non Acetone) can do the trick.

Thank you. :salute:

**Freddybear[TK]** · September 1, 2020

Ok well that has thrown a spanner in the works. I tried taking a little off with non acetone remover and a tooth pick but it just chipped and looks terrible now. I purchased this helmet pre painted so I've had to order the paint now myself so that I can redo the frown. Will hopefully have it done at the weekend assuming the paint comes before then.

**TKSpartan[Staff]** · September 1, 2020

P.M. sent

**Freddybear[TK]** · September 1, 2020

Okay, so I tried repainting the frown with some modelling acrylic paint that I had to hand. Technically it meets requirements now but I am not really happy with the finish. It is quite thick with visible brush strokes if you look closely so I will still be cleaning it off and repainting once the proper enamel paint comes. I plan on going Centurion eventually so it will certainly be rectified before then.

Edited September 2, 2020 by Freddybear
spelling

**TKSpartan[Staff]** · September 1, 2020

Thank you Dave, I'll be with you shortly.

**TKSpartan[Staff]** · September 3, 2020

Hi Dave, and thank you for your EIB application!

CRL and EIB Application Requirements:

All required photos have been submitted, and on behalf of the entire D.O. staff we are pleased to welcome you to the rank of Expert Infantry. Congratulations! :salute:

Other-Armor Fit/Assembly;

In this area we review observations made by your fellow troopers and the DO team. Some observations may lead to suggestions to improve the overall look of your armour.

***************************************************

Let's start by the Helmet:

It seems like you have a bit of extra return edge around your eyes, especially up . To give it that menacing Stormtrooper sight you may want to trim it a bit. A few minutes of sanding or with a dremel should clean it up nicely.

Reference Images

This looks like a dressing issue , As you can see in the sections marked, Your sides are overlapping showing a noticeable gap , you may want to check the strapping adjustment to close it a get a better look.

Reference Images

Your belt is on an angle, also nearly covering the bottom ab button and it should be just "almost touching" , not a deal breaker but you can take note when dressing up.

Reference Images

Onto your canvas belt, some troopers prefer the weathered look which is fine, but we're suggesting you give your belt a bit of a haircut to trim off some of the extra threads.

Reference Images

We are suggesting to bring your thighs down a little so your shins can come down also and have a better fit by reducing the gap at your knees, also will let the to rest better over your boots.

Reference Images

***************************************************

Centurion Requirements;

In this section we prepare you for Centurion. Because Centurion photos show more detail than EIB, items pertaining to Centurion might be seen there and not here and additional photos may be required. We try to point out all that we can from what we see, but the final accuracy is the responsibility of the trooper.

CRL L3: Ab button paint shall not extend beyond the bottom of the actual raised button.

The paint on your Ab plates sticks out a little from the raised edge of the buttons.

CRL L3 :Abdominal and Kidney Plate align horizontally at top

This is likely just a dressing issue, but your ab and kidney left side rivets are misaligned . You can also consider adding or adjusting strapping to keep them better aligned.

Reference Images

CRL L3: Canvas belt must be firm/sturdy in appearance. No creasing or sagging.

The canvas belt looks as if it is fairly good as worn, but the wrinkles can not be present for L3. Mine is an RWA too and what I always do is to tighten it when dressing up for trooping.

Reference images

SKYsomw.png?1 4eW2R4K.jpg?1

CRL L3: The blaster may have minor weathering or base metal exposure however, T-tracks and grips shall have the appearance of black plastic.

Finally in this section, we have your blaster

It appears that there are some silver showing on your blaster grip, there are a couple of areas under the T track on the other side and around it front handle, perhaps not enough paint coverage.