WodiQuix[TK] Posted August 1, 2020 Report Posted August 1, 2020 Hello FISD team! For your consideration, here is my (hopefully) Centurion-ready ANH stunt TK! This armor has gone through a heck of a lot of changes, and I couldn't be more proud of how far I've come with it. Name: Ian Malinoski Forum Name: WodiQuix Legion ID: 22418 Armor Maker: RS Props Helmet Maker: RS Props Blaster Maker: DoopyDoos Boots Maker: ImperialBoots Canvas Belt Maker: Imperial Issue Hand Plate Type: White Latex Electronics: iComm and Aker Amp/microphone Neck Seal Maker: Geeky Pink Holster Maker: TrooperBay EIB Thread: Thank you again for your consideration! I'm looking forward to hearing from the experts. Quote
justjoseph63[Staff] Posted August 1, 2020 Report Posted August 1, 2020 Hi Ian, and THANKS for your submission! I will be with ya' shortly, sir. Quote
GoofTrooper[TK] Posted August 3, 2020 Report Posted August 3, 2020 Very nice armor! Good luck Trooper! Quote
WodiQuix[TK] Posted August 5, 2020 Author Report Posted August 5, 2020 After looking over a number of other Centurion applications, I decided to raise my brow trim to become a high brow-er! I think it looks pretty cool! I had always liked the low brow look, but the high brow look slowly grew on me. 1 Quote
WodiQuix[TK] Posted August 16, 2020 Author Report Posted August 16, 2020 Here are updated pictures for my Centurion submission! Quote
gmrhodes13[Staff] Posted August 16, 2020 Report Posted August 16, 2020 Nice work could you also post up some updated close up images please Sniper plate both sides Thigh ammo strip rivet Butt plate snaps Ab plates Helmet sides and vocoder Ab plate side top snap Ab plate side rivets Belt Quote
justjoseph63[Staff] Posted August 29, 2020 Report Posted August 29, 2020 Hi Ian, and sorry for the delay. Again, after going over the following items with fellow staff members we have to hold off on your submission for the time being, sad to say. As I mentioned, several of these items were fine in your EI request, but after changing out many of the components they no longer meet the requirements for Centurion level, which is all about the small details. We sincerely hope you can remedy these issues and re-submit soon, and if you require any clarification or need any help, just ask! The base of your helmet has quite a large divot as seen below the rear of the right ear. This can be effectively covered by moving the base of the ear backward, (photo 3 shows another RS helmet to give you an example). Doing this would also move them into a more screen accurate position. Many of the screen used buckets were a little wonky in certain places, but we can find no references showing any with such a large recessed area. Photo 3 Reference images (Note how screws line up with rear trap angle) The "Han" snap will need to be moved farther out toward the edge as seen in the reference images. We are also highly suggesting that you eliminate the overlap of the ab-plate on the right side. Reference images As stated in the CRL, ".. the corners of the plastic ammo belt shall be trimmed at a 45 degree angle that meets the outer edge of the cloth belt". There are 2 ways to go about fixing this.. 1. Get a cloth belt that is a bit narrower, or 2. Get a new ABS belt and leave it a bit wider when trimming in order to get the correct size on the angles (photo 2). Photo 2 Reference images Your shoulder bells will need to adjusted to where the tops are touching (or very close) to the shoulder bridges as seen in your EI submission (photo 2). Photo 2 Below is one more suggestion: Your sniper knee tops could use some trimming to give them more of an angle. EASY fix! Reference images Quote
WodiQuix[TK] Posted August 29, 2020 Author Report Posted August 29, 2020 Thank you for the suggestions and feedback! I'll take this into consideration and see what I can do! Quote
justjoseph63[Staff] Posted March 15, 2021 Report Posted March 15, 2021 This is now considered an inactive thread. Please contact any member of the D.O. staff to continue the review process Quote
equuspolo[TK] Posted March 16, 2021 Report Posted March 16, 2021 Good luck Ian. You are almost there. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.