Twelveravens[TK] Posted August 13, 2019 Author Report Share Posted August 13, 2019 Ok...first almost full suit up. Need suggestions/advice! The cod hits the top of the thighs. Looks like I need to trim cod more? Trim cod and inner thigh? Looks like i have to bring torso up a bit more too? Bring chest down a bit also??arms fit good, just need to put cover strips on biceps. Sent from my SM-T597P using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted August 13, 2019 Report Share Posted August 13, 2019 I'd suggest bringing up your ab section first and then check again what room if any there is. Ā When you compare to this there's probably half the distance from ab plate to chest compared to yours. Ā Ā Some have very minimal gap between, but most appear to have issues with the cod hitting thighs Ā 1 Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted August 13, 2019 Author Report Share Posted August 13, 2019 Ill try that first. Im so used to how/where my ANH TK fits I have to adjust for the different parts of this one. Sent from my SM-T597P using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted August 15, 2019 Author Report Share Posted August 15, 2019 Ok. Yanked the midsection up higher and it sits a little better. I threw on my ANH tk belt just to get an idea of how a belt would look on it. The cod looks a little wide near the top still? Also the rear of the thighs bump a little against the butt plate. Maybe trim about 1/2 inch off the top of the thighs to spread things out a bit? Sent from my SM-T597P using Tapatalk Quote Link to comment Share on other sites More sharing options...
MacPhisto[TK] Posted August 21, 2019 Report Share Posted August 21, 2019 Justin, this is phenomenal work.Ā All in all I'm quite impressed with your craftsmanship.Ā When you get it finished I look forward to trooping with you in my Rogue One Vader!Ā Awesome work trooper! Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted August 27, 2019 Author Report Share Posted August 27, 2019 So all major construction finally done! I hate the R1 belt btw. Have to glue on 3 more of the belt face boxes. Going to trim the top of the thighs just a bit to get them to sit a little better and improve movement. I had a hard time getting the thighs to close because I couldnt quite reach. Aloso going to improve the shoulder strap connections and add obe or two elastic straps from the ab to the inside if the chest to keep it from pulling up. All in all I think Im pretty much done. Sent from my LG-Q710AL using Tapatalk 3 Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted September 2, 2019 Author Report Share Posted September 2, 2019 All done! My left thigh is a tad high in the pictures, but its on an adjustable strap system so easily taken care of. Moving around in it is a huge difference than my ANH TK. Inalso tried on my pack and it sits better, and with the rubber straps, it helps keep the back pack straps from sliding off to the side and getting vaught under the shoulder bell. The extended/larger back also helps alleviate the weight by pushing the pack into a better vertical position. Overall I learned a lot of new things with this build. My only complaint is the belt. The all plastic construction is a pain to deal with, and I hate the notches at the top of the belt. Because of the softer details of the abs pull and how far back the bottom lip sits, it was difficult construction wise to get them in as well as I could. Sent from my SM-T597P using Tapatalk 3 Quote Link to comment Share on other sites More sharing options...
Imperial Valour[TK] Posted September 2, 2019 Report Share Posted September 2, 2019 Wow, this looks pretty good. I am having issues with the belt as well, it just doesn't line up properly. Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted September 2, 2019 Author Report Share Posted September 2, 2019 I attached one of the big flat plastic strips to the front with poprivets, and it arced out enough for gluing on the belt face and lining the slots up the best I could. Sent from my SM-T597P using Tapatalk Quote Link to comment Share on other sites More sharing options...
Sly11[Admin] Posted September 2, 2019 Report Share Posted September 2, 2019 You look great! Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted September 2, 2019 Author Report Share Posted September 2, 2019 Only a few issues I had to fix. Need to bring my back up a bit. Trim mah buttplate so I don't have saggy trooper butt. And fix my "ii" 's as I glued them on with the ridges at the top cause I wasnt paying attention to what I was doing. Sent from my SM-T597P using Tapatalk Quote Link to comment Share on other sites More sharing options...
11b30b4[TK] Posted September 4, 2019 Report Share Posted September 4, 2019 outstanding job brother Ā Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted September 11, 2019 Author Report Share Posted September 11, 2019 Approval came down today! First field test this Saturday! Sent from my SM-T597P using Tapatalk 3 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted September 11, 2019 Report Share Posted September 11, 2019 Congratulations trooper good luck on the field test Quote Link to comment Share on other sites More sharing options...
LTM[TK] Posted September 11, 2019 Report Share Posted September 11, 2019 congrats! Make the empire proud on saturday! Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted September 17, 2019 Author Report Share Posted September 17, 2019 First field test with the armor went great! The only minor issue was my left thigh drooping a bit because I didnt have the slide buckle above the quick release secured well enough. Other than that, went from 10:30am to 3:30pm in the kit, with about 3 hours with the pack on. Nothing on the armor felt too constricted and no armor bites. Pack sits great and the rubber straps kept the pack strap on place, not sliding off and resting on my shoulder caught under the bell like my Anovos kit. I even sat in a chair when helping judge the kids costume contest! Even made the local paper on the first outing! All in all, great kit, and I learned a lot more building tricks along the way to make the kit comfortable, durable, and easy to get in and out of on my own. Still not thrilled about the R1 belt design, but managed to make it semi presentable. Sent from my SM-T597P using Tapatalk 2 Quote Link to comment Share on other sites More sharing options...
gmrhodes13[Staff] Posted September 17, 2019 Report Share Posted September 17, 2019 Nice work trooper. I find with some of the buckles to double loop through the nylon or elastic helps keeping them nice and tight.Ā Quote Link to comment Share on other sites More sharing options...
zv288bot[TK] Posted September 17, 2019 Report Share Posted September 17, 2019 Looks awesome, congrats!! Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted September 24, 2019 Author Report Share Posted September 24, 2019 Trooped the Mothman Festival this weekend and got my strapping to sit better and more secure. Was able to get a few 3 hour long stints in armor even with the heat in the upper 80s. Mobility in the R1 kit is so much better. Just a few comfort tweaks to do, and some more troops to fine tune it. Sent from my SM-T597P using Tapatalk 2 Quote Link to comment Share on other sites More sharing options...
Imperial Valour[TK] Posted September 24, 2019 Report Share Posted September 24, 2019 Looks great!! Quote Link to comment Share on other sites More sharing options...
Imperial Valour[TK] Posted October 23, 2019 Report Share Posted October 23, 2019 Quick question for you on your build. How did you attach the thermal detonator to the back half of the belt? I am thinking about using rivets or velcro but I am curious how you did it. Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted October 23, 2019 Author Report Share Posted October 23, 2019 I made a block about 2 1/2" long from excess cut off from a thigh cover strip. I drilled two holes through it, the back of the TD, and the belt. I used a 3/4 pop rivet and washer through from the belt, through the block and into the TD to secure it. I'll take a picture tomorrow evening and post it. Sent from my SM-N950U using Tapatalk Quote Link to comment Share on other sites More sharing options...
cjkirk11 Posted November 4, 2019 Report Share Posted November 4, 2019 Any pictures of your belt? I am working on an 850 kit and I'm looking for ideas. Quote Link to comment Share on other sites More sharing options...
Twelveravens[TK] Posted November 4, 2019 Author Report Share Posted November 4, 2019 I'll get some pics when I get home this evening. Sent from my SM-N950U using Tapatalk Quote Link to comment Share on other sites More sharing options...
Roukie 1[TK] Posted January 8, 2020 Report Share Posted January 8, 2020 Hi Justin. Great work. The Armor looks very good. I ordered my 850 Armor Works Kit and can`t wait for BBB day. May I ask you for some Pics of the Strapping? Especially the Strapping of the Cod and Butt. Where did you attach the Strapping of the Shoulderbell/Biceps and what did you use? How wide are the Straps that hold the Tighs? Ā Thanks in advance Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.