fieldmarshall Posted February 1, 2019 Report Posted February 1, 2019 Thanks to a lot of help from this forum and special thanks to Henry Slyfox Bartsch this highly detail aluminum Ell sterling build was made possible... In the next few pages i hope to go over its assembly and finishing. Refer to my reg posting for it design , machining and casting processes. 2 Quote
fieldmarshall Posted February 1, 2019 Author Report Posted February 1, 2019 This kit is located in my online stores along with power cylinders and dozens of other SW related products.. https://www.ebay.com/itm/283271586772 https://www.ebay.com/itm/123504458103 ebay http://www.ebay.com/usr/vmusicstore http://www.warmachinepaintball.com/online-store-replicas/ You can always email me direct if you have any questions. [email protected] Quote
Alay[501st] Posted February 1, 2019 Report Posted February 1, 2019 Why would you make these available for sale when I don't have any extra money? :'( Been following this project since you first posted about it, your work is absolutely phenomenal and they look amazing. Great great great work! 1 Quote
fieldmarshall Posted February 1, 2019 Author Report Posted February 1, 2019 From here ill start adding the individual assemblies to show how the kit assembles.... Quote
fieldmarshall Posted February 1, 2019 Author Report Posted February 1, 2019 2 hours ago, Alay said: Why would you make these available for sale when I don't have any extra money? :'( Been following this project since you first posted about it, your work is absolutely phenomenal and they look amazing. Great great great work! dont worry,,, idid not do this in a quick small run ... i will have these for the future... 1 Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 First im going to start off with the stock assembly,,,,,,,,, Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 First step is to attach the main brace.... two of 10/32 set screw and a 3/32 allen key Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 Next is the spring and follower ... Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 (edited) Now the spring plate and shoulder rest...... alignment is critical and a pain in the butt.. i use a allen key to keep these item in alignment while i put the set screws in from both sides.. Both go all the way in with them yet they need to trap the pivot catch part ........ Edited February 5, 2019 by fieldmarshall Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 Make sure you place this little part in correct,, it is the tension-er for the shoulder part. once aligned first screwing in the set screws to hold it in place..... Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 NEXT THE MAG WELL ASSEMBLY Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 Notice the stamping on the smaller parts ,,,, Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 1/8 inch allen key for the 1/4-28 set screw Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 Special note !!! make sure you have the mag catch correct side up ... Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 Mount to my alum tube body is easy,,,, Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 your can pull it up really tight for a seamless fit.... any small seem can be filled before painting .. Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 (edited) Check the mag hole in the tube if there is any hang over trim it with a dremel or a file so it will not interfere with the mag Edited February 5, 2019 by fieldmarshall Quote
fieldmarshall Posted February 5, 2019 Author Report Posted February 5, 2019 BOLT AND SPRING ASSEMBLY 1 Quote
fieldmarshall Posted February 12, 2019 Author Report Posted February 12, 2019 Spring first then the 5/32 x3/8 dowel Quote
fieldmarshall Posted February 12, 2019 Author Report Posted February 12, 2019 (edited) I did shorten the smaller springs length to help with re weenie it doesn't show and makes things smoother.......... after all its not returning to bolt blow back Edited February 12, 2019 by fieldmarshall Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.