Rietzer[TK] Posted January 4, 2019 Report Posted January 4, 2019 Name: Luis Sedeño Galán 501st Id: TK-31513 FISD Forum Name: Rietzer Garrison: Spanish Garrison 501st STATUS: http://www.501st.com/members/displaymemberdetails.php?userID=23149 Mandatory Information Armor: Armour Factory Props Helmet: Armour Factory Props Blaster: E-11 Armour Factory Props Optional Height: 1.85 cm Weight: 85 kg Boots: Armour Factory Props Canvas Belt: Armour Factory Props Hand Plates: Armour Factory Props Neck Seal: Armour Factory Props Holster Maker: Armour Factory Props Best regard Quote
gmrhodes13[Staff] Posted January 4, 2019 Report Posted January 4, 2019 4 hours ago, troopermaster said: Who made your armour? Link to FB page https://www.facebook.com/infoAFProps/ Quote
Rietzer[TK] Posted January 5, 2019 Author Report Posted January 5, 2019 Good Day!! This armour was made by the Armour Factory guys. You can see all their products in www.armour-factory.com Quote
password[TK] Posted January 5, 2019 Report Posted January 5, 2019 (edited) Cool. A great armor and a great job Congratulations. Edited January 5, 2019 by password . 1 Quote
justjoseph63[Staff] Posted January 6, 2019 Report Posted January 6, 2019 Thank you for your submission, Luis! One of us will be with you shortly. While you are waiting, it may be the photo, but it looks as if the paint has been pretty severely scratched on your left cheek trap. Could you post up a new pic of this, as well as one of close-up, clear side view of the inside of your sniper knee plate connection? Thanks!! 1 Quote
Rietzer[TK] Posted January 7, 2019 Author Report Posted January 7, 2019 Good day!!! Publish photos you requested, thank!!! Best regards Quote
justjoseph63[Staff] Posted January 11, 2019 Report Posted January 11, 2019 Hi Luis, and thank you for your EI submission! CRL and EIB Application Requirements: All required submission photos have been posted, and I am very pleased to announce your armor displays all the necessary elements to qualify for ANH Stunt Expert Infantry. On behalf of the entire D.O. staff, congratulations! Other-Armor Fit/Assembly: In this section we review observations made by your fellow troopers and ourselves. Some observations may lead to suggestions to improve the overall look of your armor. First, really nice job on this armor, sir. Since this is your second EI submission, you are familiar with the fact that the higher levels are all about the details, and we have just a few to go over so let's dive right in! Starting at the vocoder, the top looks a little squared off. A few minutes with a round tip "Filbert" style artist's brush would really make it look a lot more defined. Reference image Filbert brush Your right shoulder bell is sitting much lower than the left one. This looks to be a simple matter of tightening up the elastic that connects it to the shoulder bridge so that it matches your left one. Reference image Your posterior (butt) plate is riding over your kidney plate quite a bit. Since you used the "classic" strapping system, I recommend tightening up the elastic on the bottom center posterior/kidney connection. This should tighten them up and keep this from happening. Reference images In your main photo your ABS belt is in the ideal position, (covering the bottoms of your ab-button plates), but in your "action shot" it appears to be much lower. You may want to check the snaps that hold it in place. Side note: AWESOME job on those ab button covers!! Reference image Your TD should be a LOT lower than it is right now. It looks as if it is not pushed all the way down, but even if it were it would still be higher than it should. The top should be at the same level as the top of your canvas belt, so we are suggesting that you reposition or replace the clips. Reference image Reference image You did a fantastic job on your left rear calf connection, but the right one needs some work. The cover strip should be a lot nearer to the center as seen in the reference image. Reference image You have a sharp looking blaster there, but a few minutes with some spray paint could really make it look a lot more screen accurate! Having some brass coloring on the scope is nice, but there is quite a bit more than needed. It may be the glare of the photo, but it looks like there is also some on the barrel below the charging handle area. It also appears that there is weathering on your T-tracks. Since these were made of black plastic, there should be none. Reference images Lastly, note that the handles (grips) on the Sterlings used were also made of plastic, which should have a shiny black finish and no weathering. Reference image Centurion Suggestions:In this section we prepare you for Centurion. More photos may be requested that allow us to make better decisions on possible adjustment etc. If there are any areas of concern they will be discussed here. Because Centurion photos show much more detail than EIB, items pertaining to Centurion might be seen there and not here. We try to point out all we can from what is seen but the final accuracy is the responsibility of the trooper. As per the CRL, "The plastic shoulder straps need to be held down in the back via a white elastic band to the white fabric that connects/bridges the chest and back piece". Reference image Unfortunately, the rivets on your ab plate will need to be moved, Luis. As per the CRL, Rivets are equally spaced along the depth of the armor and about 10mm from the edgeThe ones on your kidney align correctly, and are properly spaced from the bend at the return edge (blue line). However, since your ab plate has no return edge they need to be much closer as shown in the reference image below. Moving them and filling the holes is actually not as difficult as it may seem, and there is a great tutorial on how to make ABS paste to accomplish this. Reference image Since you obviously have the talent, I have every confidence that you can make these changes, and I look forward to seeing you add yet another Centurion award to your profile! 1 Quote
gmrhodes13[Staff] Posted January 11, 2019 Report Posted January 11, 2019 Congratulations trooper 1 Quote
CableGuy[TK] Posted January 11, 2019 Report Posted January 11, 2019 Well done, Luis. Great job. :-) 1 Quote
Rietzer[TK] Posted January 12, 2019 Author Report Posted January 12, 2019 Thank you very much I am very happy to get the IE in my second suit, thank you for your time and help to achieve this achievement.Thank you very much for all the comments and recommendations so that my AFP armor gets the centurion level.From today I start working on it. Best regards. 2 Quote
justjoseph63[Staff] Posted January 12, 2019 Report Posted January 12, 2019 8 minutes ago, Rietzer said: Thank you very much I am very happy to get the IE in my second suit, thank you for your time and help to achieve this achievement.Thank you very much for all the comments and recommendations so that my AFP armor gets the centurion level.From today I start working on it. Best regards. That's the spirit, Luis, nice to hear!! 1 Quote
Forestrooper[TK] Posted January 12, 2019 Report Posted January 12, 2019 Congratulations Luis. Very good job! Ha quedado genial, enhorabuena! 1 Quote
Chips[TK] Posted January 12, 2019 Report Posted January 12, 2019 Congrats Luis! Eres un crack 1 Quote
Rietzer[TK] Posted January 12, 2019 Author Report Posted January 12, 2019 Thank you very much partners!!! Muchas gracias compañeros!!! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.