TKModder421[TK] Posted March 18, 2019 Author Report Posted March 18, 2019 On 3/18/2019 at 7:46 PM, TK 71627 said: That would be PERFECT if you had access to one !!! Expand Right, I'd probably have to buy one. Quote
TK 71627[TK] Posted March 18, 2019 Report Posted March 18, 2019 I’ve seen some at Walmart and dollar general.....probably less expensive than getting new set of thighs...Sent from my iPhone using Tapatalk Quote
TK 71627[TK] Posted March 18, 2019 Report Posted March 18, 2019 What about asking friends.... it would be easier.... yes/no ???Sent from my iPhone using Tapatalk Quote
TKModder421[TK] Posted March 18, 2019 Author Report Posted March 18, 2019 On 3/18/2019 at 8:02 PM, TK 71627 said: I’ve seen some at Walmart and dollar general.....probably less expensive than getting new set of thighs... Expand On 3/18/2019 at 8:04 PM, TK 71627 said: What about asking friends.... it would be easier.... yes/no ??? Expand I'll definitely take a look at more inexpensive options Yes! I'm actually asking friends right now. We'll see what I can come up with Thanks Jose! 1 Quote
TKModder421[TK] Posted April 1, 2019 Author Report Posted April 1, 2019 Borrowed a giant stock pot from a friend. Worked perfectly for the hot water bath on the thighs 2 Quote
TKModder421[TK] Posted April 1, 2019 Author Report Posted April 1, 2019 Attached the cover strip to the right thigh You can see my magnets are off center near the top, that was to press down the strip where there was a gap Here's the left side Quote
TKModder421[TK] Posted April 1, 2019 Author Report Posted April 1, 2019 So after 24 hours I removed all the clamps, magnets and tape and the right thigh turned out great! The left thigh didn't turn out as great though I didn't notice when I was clamping down the cover strip but the ridge where the cover strip rest on has a curve to it. I put a green dotted line on it so you can see it a bit better While normally I wouldn't worry too much, when I was trimming I made the ridge 10mm on both sides all the way up, but I didn't take into account that there was a curve. So now when the cover strip lays on there flat, I end up with this ridge being exposed on the right and a slight overhang on the left side of the cover strip. I'm aiming for upper level approval so I'm gonna rip it off and try again. But I'm wondering what would be the best way to fix this problem. I've noticed on thigh reference pics that a lot of the cover strips have a bend to them to follow the cut lines I assume. Should I attempt to heat up the strip and add a bend to match the ridge or what I should do?? Help!!! 1 Quote
gmrhodes13[Staff] Posted April 1, 2019 Report Posted April 1, 2019 You will find the abs strips can be bent with addition of some pressure, ie using painters tape. I use clamps magnets and painters tape, all do a job in their own way, the tape will just allow a little more pressure to be given to the cover strips for either downwards or sidewards needs With E6000 you can just pull off again and rub off the glue, then reapply 1 Quote
TKModder421[TK] Posted April 2, 2019 Author Report Posted April 2, 2019 On 4/1/2019 at 10:21 PM, gmrhodes13 said: You will find the abs strips can be bent with addition of some pressure, ie using painters tape. I use clamps magnets and painters tape, all do a job in their own way, the tape will just allow a little more pressure to be given to the cover strips for either downwards or sidewards needs With E6000 you can just pull off again and rub off the glue, then reapply Expand OK, thank you! I'll give it a try and see what I can do. Thank goodness for E6000!! 1 Quote
TK 71627[TK] Posted April 2, 2019 Report Posted April 2, 2019 On 4/1/2019 at 4:47 PM, TKModder421 said: Borrowed a giant stock pot from a friend. Worked perfectly for the hot water bath on the thighsWAY TO GO, TROOPER !!!Sent from my iPhone using Tapatalk 1 Quote
TK 71627[TK] Posted April 2, 2019 Report Posted April 2, 2019 On 4/1/2019 at 7:39 PM, TKModder421 said: So after 24 hours I removed all the clamps, magnets and tape and the right thigh turned out great! The left thigh didn't turn out as great though I didn't notice when I was clamping down the cover strip but the ridge where the cover strip rest on has a curve to it. I put a green dotted line on it so you can see it a bit better While normally I wouldn't worry too much, when I was trimming I made the ridge 10mm on both sides all the way up, but I didn't take into account that there was a curve. So now when the cover strip lays on there flat, I end up with this ridge being exposed on the right and a slight overhang on the left side of the cover strip. I'm aiming for upper level approval so I'm gonna rip it off and try again. But I'm wondering what would be the best way to fix this problem. I've noticed on thigh reference pics that a lot of the cover strips have a bend to them to follow the cut lines I assume. Should I attempt to heat up the strip and add a bend to match the ridge or what I should do?? Help!!! I would attempt to bend it , or just make the cover strip like 14mmSent from my iPhone using Tapatalk Quote
TKModder421[TK] Posted April 2, 2019 Author Report Posted April 2, 2019 On 4/2/2019 at 5:33 AM, TK 71627 said: I would attempt to bend it , or just make the cover strip like 14mm Expand Would I be affecting my chances of EIB or Centurion approval if I cut down the width of the cover strip? Quote
TK 71627[TK] Posted April 2, 2019 Report Posted April 2, 2019 On 4/2/2019 at 5:41 AM, TKModder421 said: Would I be affecting my chances of EIB or Centurion approval if I cut down the width of the cover strip?Why just leave ur cover strip at 10mm just trim the excess just a hair ..... it will LOOK GOOD ON THE OUTSIDE....and u can always “reinforce” it with an inside cover strip . It won’t show .Sent from my iPhone using Tapatalk Quote
TK 71627[TK] Posted April 2, 2019 Report Posted April 2, 2019 On 4/2/2019 at 5:41 AM, TKModder421 said: Would I be affecting my chances of EIB or Centurion approval if I cut down the width of the cover strip?No ! ....Both cover strips have to be the same length.... just do like I tell u ...Sent from my iPhone using Tapatalk Quote
TK 71627[TK] Posted April 2, 2019 Report Posted April 2, 2019 On 4/2/2019 at 5:47 AM, TK 71627 said: No ! ....Both cover strips have to be the same length.... just do like I tell u ...Sent from my iPhone using TapatalkCover strips BOTH have to be symmetrical....Sent from my iPhone using Tapatalk Quote
TK 71627[TK] Posted April 2, 2019 Report Posted April 2, 2019 On 4/2/2019 at 5:49 AM, TK 71627 said: Cover strips BOTH have to be symmetrical....Sent from my iPhone using TapatalkI meant WIDTH.... cover strips just need to be the same width !Sent from my iPhone using Tapatalk Quote
TK 71627[TK] Posted April 2, 2019 Report Posted April 2, 2019 Hey, 421.... I have my thigh cover strips at 20mm ....Sent from my iPhone using Tapatalk Quote
TK 71627[TK] Posted April 2, 2019 Report Posted April 2, 2019 Hey, 421 I used this TK diagram for my cover strips Sent from my iPhone using Tapatalk Quote
TKModder421[TK] Posted April 2, 2019 Author Report Posted April 2, 2019 On 4/2/2019 at 5:57 AM, TK 71627 said: Hey, 421.... I have my thigh cover strips at 20mm .... Expand Yeah, that's the width mine are as well. But since my right thigh is already glued and looks good I feel it would be better to bend it a little than to trim them both down Quote
TK-42775[TK] Posted April 2, 2019 Report Posted April 2, 2019 With gluing the cover strips, I have found it easier to only do one side at a time, Yes it's more time consuming but you get more control over how it goes down 1 Quote
justjoseph63[Staff] Posted April 2, 2019 Report Posted April 2, 2019 Not to be "indelicate" here, but if you haven't glued the backs of the thighs yet I would suggest removing the return edge in the area shown below and then resizing them. Consider that you will be doing quite a bit of walking, and in doing so the lower part of the ab and the cod may apply pressure to those return edges (especially in the center) which can cause serious chafing. Just a heads-up. Quote
TKModder421[TK] Posted April 2, 2019 Author Report Posted April 2, 2019 On 4/2/2019 at 10:25 AM, James Whitley said: With gluing the cover strips, I have found it easier to only do one side at a time, Yes it's more time consuming but you get more control over how it goes downYeah I agree! Thanks James 1 Quote
TKModder421[TK] Posted April 2, 2019 Author Report Posted April 2, 2019 On 4/2/2019 at 10:44 AM, justjoseph63 said: Not to be "indelicate" here, but if you haven't glued the backs of the thighs yet I would suggest removing the return edge in the area shown below and then resizing them. Consider that you will be doing quite a bit of walking, and in doing so the lower part of the ab and the cod may apply pressure to those return edges (especially in the center) which can cause serious chafing. Just a heads-up. Oh really?? Shoot! I wish I would've known this before. Trimming these thighs has been a pain lol. I think that would've made things a lot easier.I do already have the back strip on the right thigh. Second to upper level approval, comfort is my next priority though. You suggest taking that one apart and taking the return edge off both? Just the inside of the thighs? Will it look strange having return return edge on the outside of the thigh and not on the inside? Do you have any images of how it should look when I do this? Quote
TheSwede[TK] Posted April 2, 2019 Report Posted April 2, 2019 On 4/2/2019 at 4:40 PM, TKModder421 said: Oh really?? Shoot! I wish I would've known this before. Trimming these thighs has been a pain lol. I think that would've made things a lot easier. I do already have the back strip on the right thigh. Second to upper level approval, comfort is my next priority though. You suggest taking that one apart and taking the return edge off both? Just the inside of the thighs? Will it look strange having return return edge on the outside of the thigh and not on the inside? Do you have any images of how it should look when I do this? Expand You don´t have to take the thigh apart, just use a dremel and sand it down gradually And as for the front cover strip I would take it off and bend it as you said to conform to the ridge Quote
TKModder421[TK] Posted April 2, 2019 Author Report Posted April 2, 2019 On 4/2/2019 at 7:56 PM, TheSwede said: You don´t have to take the thigh apart, just use a dremel and sand it down gradually And as for the front cover strip I would take it off and bend it as you said to conform to the ridge Expand Thanks Daniel, so you also recommend I take off the return edge on the upper thigh? Yeah I can definitely cut down the return edge with my Dremel, I think Joseph's concern was that it would then change the fitting of the thigh. The return edge I currently have is approximately 7-10mm, so if I take off most or all of the return edge without refitting it's going to add a gap of anywhere from 14-20mm at the top of my thigh. On my left thigh, I already took off the front cover strip so I can just cut off the return edge and then do a test fitting. But my right thigh is finished, do you think maybe I should Dremel it down and then see how that fits and then decide whether I need to resize from there? If I'm going to do that I'll probably start with the finished thigh, so if I decide it fits fine then I wont have to do any resizing Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.