tydirium1[TK] Posted February 3, 2018 Report Posted February 3, 2018 Have you glued the shins together yet? Quote
Rat[TK] Posted February 3, 2018 Author Report Posted February 3, 2018 No just working on final fitting or them now, but this is what I'm looking at. Perhaps it's normal? I'm unsure so this is why I'm bringing it up now since I'm almost to that section.Sent from my VK815 using Tapatalk Quote
tydirium1[TK] Posted February 3, 2018 Report Posted February 3, 2018 That looks about normal, believe it or not. It will fit a little better after you place the cover strip on , which runs all the way up and under the knee plate. when gluing it on be sure to do the middle with a really good clamp and then glue the sides. Quote
Rat[TK] Posted February 3, 2018 Author Report Posted February 3, 2018 That looks about normal, believe it or not. I thought perhaps it was, but couldn't be sure, I figured the sides were normal. It was the bottom I wasn't too sure about. I'm using the E-6000 for my glue, but man I keep thinking I might want to get some gel ca for this part. LOL!Sent from my VK815 using Tapatalk Quote
tydirium1[TK] Posted February 3, 2018 Report Posted February 3, 2018 The open area that you see from the top between the shin and knee plate will still be there. And there will likely be some gaps on the underside close to the cover strip Your coming along nicely. Quote
tydirium1[TK] Posted February 3, 2018 Report Posted February 3, 2018 Keep using the E 6000. If you do make a mistake on the knee plate , you can take it apart and retry. Clamping that sucker together can be a trick sometimes. It likes to move while being clamped because of the angles. Quote
Rat[TK] Posted February 3, 2018 Author Report Posted February 3, 2018 Thanks! I know there will be some gap at the top and am expecting that. Man I don't know that I've ever been so Leary or full of doubts on a project as I am here, but slow wins the race and leave little room for errors. I am debating on doing a bit of shimming shimming for the plate as I go into the legs and the way they are fitting so far.Sent from my VK815 using Tapatalk Quote
Rat[TK] Posted February 3, 2018 Author Report Posted February 3, 2018 Keep using the E 6000. If you do make a mistake on the knee plate , you can take it apart and retry. Clamping that sucker together can be a trick sometimes. It likes to move while being clamped because of the angles. Yeah I most likely will because of that and I hear the ears and this plate are the worst parts.Sent from my VK815 using Tapatalk Quote
tydirium1[TK] Posted February 3, 2018 Report Posted February 3, 2018 The ears are an exercise in futility. Trim the front and it changes the back , trim the back to help the front , now the top and bottom don't fit any more. so you scratch your head and say maybe it will fit tomorrow. Lol. Good luck with the rest of the build. I'll keep an eye on your build. Looks like it's going to turn out good. 2 Quote
Rat[TK] Posted February 3, 2018 Author Report Posted February 3, 2018 Again thank you. Over all I'm pretty positive and optimistic still. Also still avoiding that right forearm. LOL!Sent from my VK815 using Tapatalk Quote
Rat[TK] Posted February 14, 2018 Author Report Posted February 14, 2018 Alright the plague has passed and feeling much better so time to get back at it. I think it is leg day and then I need to work out how to do the fitting and sizing of the body alone. The legs so far have been a 50/50 so far as ease goes. Any ideas of how I could manage this?Sent from my VK815 using Tapatalk Quote
Rat[TK] Posted February 21, 2018 Author Report Posted February 21, 2018 Slow going, but halfway through the forearms. Had a slight mishap with using a heat gun to reshape the right one. Luckily I caught it before it got too bad. Not happy about it but it's serviceable and doesn't stand out too much.Sent from my VK815 using Tapatalk Quote
Rat[TK] Posted February 21, 2018 Author Report Posted February 21, 2018 5 minutes ago, ukswrath said: Close call whew! Indeed. I noticed it happening and pull the heat and started blowing. LOL! On 1/31/2018 at 5:57 AM, ukswrath said: And that's why this armor bothers me so. Looking at the photo below (properly installed) logically the armor should feel natural but I'm guessing it doesn't. One thing is for certain the lines of the armor follow the contour of your leg muscle. Once you through on some boots you'll feel right as rain. Hahaha! Yeah I just threw them on really quick before getting ready for work so didn't have time to get the boots out. Quote
Rat[TK] Posted February 22, 2018 Author Report Posted February 22, 2018 So not sure this needs a picture or not, but my thighs and shins fit well with no real need to trim more. However the back of them don't line up great, the top and bottom butt together, but there's a slight gap in the middle and I'm not sure what to do. My concern is if I trim them more they'll be too tight. Any advice or ideas would be great.Sent from my VK815 using Tapatalk Quote
gmrhodes13[Staff] Posted February 22, 2018 Report Posted February 22, 2018 Pictures would help, but as long as a cover strip will cover this area there shouldn't be an issue, adding an internal strip would also help to cover and add strength to the area. 1 Quote
Rat[TK] Posted February 22, 2018 Author Report Posted February 22, 2018 Yeah mostly it is with the shins. I end up with like a 1/4" or 15-20 mm gap right in the middle. I'll dig it out and get a picture.Sent from my VK815 using Tapatalk Quote
Rat[TK] Posted February 22, 2018 Author Report Posted February 22, 2018 I guess it's more like 5mm.Sent from my VK815 using Tapatalk Quote
68Brick[TK] Posted February 22, 2018 Report Posted February 22, 2018 The cover strip should cover that up no problem. And, adding an internal cover strip is a must. Shins see a lot of force on them when putting them on and off. Also, put the heat gun away! Try a hot water bath instead. Heat guns are not forgiving, and many have had parts ruined by their fiery breath. Keep up the good work! 1 Quote
Rat[TK] Posted February 22, 2018 Author Report Posted February 22, 2018 Yeah no more heat gun for me to close a call on the forearm. I may trim just a hair off the top and bottom. By hair I mean 1 or 2 mm which is mostly remnant anovos line. Sanding may do better than cutting.Sent from my VK815 using Tapatalk 1 Quote
gmrhodes13[Staff] Posted February 22, 2018 Report Posted February 22, 2018 57 minutes ago, Rat said: Yeah no more heat gun for me to close a call on the forearm. I may trim just a hair off the top and bottom. By hair I mean 1 or 2 mm which is mostly remnant anovos line. Sanding may do better than cutting. Everything in small steps, a heat gun on plastic takes some practice, if I saw then what I do with one now I'd freak 1 Quote
Rat[TK] Posted February 22, 2018 Author Report Posted February 22, 2018 So find myself in another quandry. Left forearm looks good, but the lower seam isn't meeting up at the return edge. Should I pull it and redo it or is it okay? It's on the bottom and unlikely to be seen, but not sure.Sent from my VK815 using Tapatalk Quote
ukswrath[Staff] Posted February 22, 2018 Report Posted February 22, 2018 I would be more concerned about if the cover strip is adequately holding the two halves together. If you think it's strong enough leave it. If the gap bothers you either finish removing the return edge or add scrap behind the gap to conceal it. 1 Quote
Rat[TK] Posted February 22, 2018 Author Report Posted February 22, 2018 I would be more concerned about if the cover strip is adequately holding the two halves together. If you think it's strong enough leave it. If the gap bothers you either finish removing the return edge or add scrap behind the gap to conceal it. Yeah it is only about 1/4" or so and the bond seems pretty firm. Still need to get it test fitted with my under suit on to be sure it isn't going to be an issue.Sent from my VK815 using Tapatalk Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.