darthcue[TK] Posted January 14, 2018 Report Posted January 14, 2018 24 minutes ago, yoshix said: I forgot to mention that I decided to glue down the kidney plate. That way it always sits flush on the one side. I put a snap on the bottom of the opposite side to close it. i think your backplate is upside down? Quote
yoshix[TK] Posted January 14, 2018 Author Report Posted January 14, 2018 (edited) 2 hours ago, darthcue said: i think your backplate is upside down? That's actually the way it came. I rounded the top so that it fits under the back plate better. I suppose I could have rounded the bottom to be more accurate as well but at the moment I'm not worried about it. Edited January 15, 2018 by yoshix 1 Quote
Dragon_a[TK] Posted January 15, 2018 Report Posted January 15, 2018 23 hours ago, yoshix said: I used fabric that hopefully looks enough like the screen used helmets. That way they still let air in. That's a fantastic idea. I think I even have an old tshirt that would be the right colour..... 1 Quote
yoshix[TK] Posted January 16, 2018 Author Report Posted January 16, 2018 I was able to paint the thighs today and hopefully (with my wife's participation) I can get some pictures tomorrow. I started on the backpack. the first thing is the white canisters are too small so I'm remaking them using some tubing I had lying around. I cut circles and glued them to the ends to seal them up. Then I resined them. It made some tiny bubble in some areas, if they don't sand out I'll have to resin them again. Quote
THMAustin Posted January 16, 2018 Report Posted January 16, 2018 I used fabric that hopefully looks enough like the screen used helmets. That way they still let air in. It would be great to see pic of that. Sent from my iPhone using Tapatalk Quote
yoshix[TK] Posted January 18, 2018 Author Report Posted January 18, 2018 On 1/16/2018 at 9:45 AM, THMAustin said: It would be great to see pic of that. Sent from my iPhone using Tapatalk I keep forgetting to take a few pictures of some spots. Maybe soon I'll remember Quote
yoshix[TK] Posted January 18, 2018 Author Report Posted January 18, 2018 Had another great test fit, I learned a lot. I'll be making some changes as I found some problems. For one the butt plate is too low. Also the shoulder bells need to be higher more flush with the sholder straps. I'm still not happy with the shins. I think my mods helped but I'm looking into some alternative. I really don't want to rebuild them 3 Quote
Parquette[TK] Posted January 18, 2018 Report Posted January 18, 2018 Yowza!!! The only major adjustment glaring at me would be the cod piece. I think it's a little 2 wide, and should be taken in a little. Remember, these are much more mobile, meaning bigger gaps in between the armor parts. Quote
yoshix[TK] Posted January 19, 2018 Author Report Posted January 19, 2018 (edited) I've been getting some work done on the backpack, if you want to see more pictures of that process check out http://forum.mepd.net/index.php?/topic/15485-yoshs-build/&page=3&tab=comments#comment-198969 Edited January 19, 2018 by yoshix 1 Quote
yoshix[TK] Posted January 19, 2018 Author Report Posted January 19, 2018 Here's what I got done today. I cut the armpit line down even more and cut he bottom of the belt line off. That way I have room to bring the butt plate up under the belt. I noticed that the two halves of the belt aren't lining up right so I moved this snap down just a little. Hopefully that will do the trick. I noticed that the straps that run between the chest and back were getting caught on the kidney plate, so I trimming them down as well. 1 Quote
yoshix[TK] Posted January 23, 2018 Author Report Posted January 23, 2018 My solution for the brow line was cut off the black top, sand it and glue it back on. It took about 1/8 off. I also had to cut a little off the back of the cap so that it lines up. The tape is just to hold it together for now. I want to make sure I'm not doing anything else to the helmet before I glue it together. Quote
Parquette[TK] Posted January 23, 2018 Report Posted January 23, 2018 Darn it, you made me realize mine was so much more elaborate xD Seriously, great job! Considering the only part you needed to paint was the rear of the helmet! Quote
yoshix[TK] Posted January 24, 2018 Author Report Posted January 24, 2018 22 hours ago, Parquette said: Darn it, you made me realize mine was so much more elaborate xD Seriously, great job! Considering the only part you needed to paint was the rear of the helmet! Lol! I read your mod and was a little confused, some of the pictures aren't showing up. Quote
yoshix[TK] Posted January 24, 2018 Author Report Posted January 24, 2018 I haven't been posting here because all the work I've gotten done lately is on the backpack and posted on mepd. Fingers crossed I should be done this weekend 1 Quote
bradberry00 Posted January 24, 2018 Report Posted January 24, 2018 (edited) On 1/22/2018 at 7:58 PM, yoshix said: My solution for the brow line was cut off the black top, sand it and glue it back on. 1 1 What did you use to cut the brow trim off with? Edited January 24, 2018 by bradberry00 Quote
yoshix[TK] Posted January 24, 2018 Author Report Posted January 24, 2018 9 hours ago, bradberry00 said: What did you use to cut the brow trim off with? I used a bandsaw but you could use a Dremel or jigsaw. Try to keep the line as strigh as possible. Also I definitely recommend a belt sander to trim off the rest of the white part and straighten it out 1 Quote
Parquette[TK] Posted January 25, 2018 Report Posted January 25, 2018 What'd you use for the boxes on the backpack? I know you had the smaller parts 3d printed, but I'm curious about the boxes. Quote
darthcue[TK] Posted January 25, 2018 Report Posted January 25, 2018 Pack is D O N E Your pack is looking good bro!Sent from my iPhone using Tapatalk Quote
yoshix[TK] Posted January 29, 2018 Author Report Posted January 29, 2018 On 1/24/2018 at 11:10 PM, Parquette said: What'd you use for the boxes on the backpack? I know you had the smaller parts 3d printed, but I'm curious about the boxes. It's a little hard to explain. They are made of a Styrofoam with paper on top and bottom. Check out my backpack build thread http://forum.mepd.net/index.php?/topic/15485-yoshs-build/& 1 Quote
yoshix[TK] Posted January 29, 2018 Author Report Posted January 29, 2018 Got some photos today Looks like the Hot Toys figure right This has been a really long and hard project but I'm happy with how it looks. I think the backpack really exceeded my expectations. 4 Quote
Dragon_a[TK] Posted February 2, 2018 Report Posted February 2, 2018 Congratulatuons on your approval and becoming the crl model. https://databank.501st.com/databank/Costuming:TD_R1_Jedha_Sandtrooper 2 Quote
yoshix[TK] Posted February 2, 2018 Author Report Posted February 2, 2018 26 minutes ago, Dragon_a said: Congratulatuons on your approval and becoming the crl model. https://databank.501st.com/databank/Costuming:TD_R1_Jedha_Sandtrooper Thank you! This is such an honor 2 Quote
CT Mac Posted February 2, 2018 Report Posted February 2, 2018 Stunning work, well done! Looks absolutely amazing 1 Quote
TheSwede[TK] Posted February 2, 2018 Report Posted February 2, 2018 Looks really great - a salute is in order 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.