ukswrath[Staff] Posted October 31, 2017 Report Posted October 31, 2017 Looking to get some specs on the TLJ Laser Ax? I figured starting a thread where whoever wants to input can do it here. Everything about the Ax is up for discussion. Post away 2 Quote
First0rder[TK] Posted October 31, 2017 Report Posted October 31, 2017 (edited) Thanks Tony, ****This maybe no longer valid as the latest measurements from Sing are that the Ax is 5ft (152cm) long, 2ft (61cm) for the claw section and 3ft (91cm) for the handle. This is all based on a Reference to the FO Trooper being 71" tall (5',11"0) Trooper Measured off of a Reference photo was: 2.92" tall Trooper - 2.92 (Ref Photo Meas) x 12" = 35.04 x 12" = 420.48 / 71 = 5.92 Decimal, 71" Tall, 180CM Math Check: 71" / 12" = 5.92 From the same Reference photo, the FO was holding an Axe, so then i measured the Axe full length (A)., Handle (H), and Top portion where the claws are (T) Axe Full Length - 2.125 (Ref Photo Meas) x 12" = 25.5 x 12" = 360 / 71 = 4.31 Decimal, 51.7" Tall, 131CM Axe Handle - 1.3125 (Ref Photo Meas) x 12" = 15.75 x 12" = 189 / 71 = 2.66 Decimal, 31.92" Tall, 81CM Axe Top - 0.75 (Ref Photo Meas) x 12" = 9 x 12" = 108 / 71 = 1.52 Decimal, 18.24" Tall, 46CM Summary Trooper - 71" Tall, 180CM Axe Full Length - 51.7" Tall, 131CM Axe Handle - 31.92" Tall, 81CM Axe Top - 18.24" Tall, 46CM If someone can double check and or share your own measurements then we can compare. Hope this helps. thanks all Edited November 20, 2017 by First0rder Quote
ukswrath[Staff] Posted October 31, 2017 Author Report Posted October 31, 2017 Awesome thanks Andrew Quote
JAFO[TK] Posted October 31, 2017 Report Posted October 31, 2017 In starting a scratch build I did some basic extrapolations and my measurements are within an inch or two of the above measurements. I reckon your calculations are solid so will take those onboard if I start the scratch again.For now I await the imminent arrival of a Laser Ax from Diversity 3D!Sent from my iPhone using Tapatalk Pro Quote
First0rder[TK] Posted October 31, 2017 Report Posted October 31, 2017 12 minutes ago, JAFO said: In starting a scratch build I did some basic extrapolations and my measurements are within an inch or two of the above measurements. I reckon your calculations are solid so will take those onboard if I start the scratch again. For now I await the imminent arrival of a Laser Ax from Diversity 3D! Sent from my iPhone using Tapatalk Pro Me too! Ive checked with Wayne as well to see where his measurements were and we were within 1" of each other. For the Top portion we were both exactly at 46cm. The handle was the only discrepancy where we were 1.5" apart. Wayne had 76cm and i had 81cm. Not bad. 1 Quote
JAFO[TK] Posted November 1, 2017 Report Posted November 1, 2017 Me too! Ive checked with Wayne as well to see where his measurements were and we were within 1" of each other. That’s brilliant !So nice when troopers show interest and actively (and openly) share their findings to get to the best end result...for everyone.What a community!Sent from my iPhone using Tapatalk Pro Quote
gmrhodes13[Staff] Posted November 1, 2017 Report Posted November 1, 2017 Mines close to those figures 50cm for head section and 80cm for handle Quote
First0rder[TK] Posted November 1, 2017 Report Posted November 1, 2017 Sound great and cant wait to see these gents. For sound, i purchased the Disney 1/2 size axe for $30 as was a good price just for the Sound card. It has was sounds like a single speaker located in the Henglester and must have a motion sensor as offers Clashing Sound when stricken. Im thinking between the few of us we can integrate this into our Axe builds and potentially upgrade the speaker a bit. Andy Quote
gmrhodes13[Staff] Posted November 20, 2017 Report Posted November 20, 2017 Nice shot of the laser ax blade overlap 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.