Commander Gree[501st] Posted July 12, 2018 Report Posted July 12, 2018 @salshred here you go buddy Quote
mark23 Posted July 12, 2018 Report Posted July 12, 2018 On 6/12/2018 at 3:53 AM, justjoseph63 said: A photo showing a wider area of what you are trying to work on would help as well. I would also recommend sanding down the area first to get rid of the dark areas, as the ABS paste may not cover these. Also, what are the dark lines? (Red arrows). Sorry to take time to respond. the dark line are weathering, but i chosed to command a new set of thight case the gap behind was to wide! Quote
fishgoh0nk[TK] Posted February 24, 2020 Report Posted February 24, 2020 @kman I'm looking to ABS paste the seams in my thigh shims, but not sure if I should leave more room for the ABS paste to sit in, or less. I haven't worked with ABS paste before, and using the plastic from ANOVOS, would you say 1-2mm is too narrow? I'm just afraid of flex that would unseat the paste because there wasn't enough to either build adhesion to the crevice walls or enough paste to provide the flex. Here's my planned material - I can trim the added material per recommendation. Quote
Harbinger[IPM] Posted February 24, 2020 Report Posted February 24, 2020 24 minutes ago, fishgoh0nk said: @kman I'm looking to ABS paste the seams in my thigh shims, but not sure if I should leave more room for the ABS paste to sit in, or less. I haven't worked with ABS paste before, and using the plastic from ANOVOS, would you say 1-2mm is too narrow? I'm just afraid of flex that would unseat the paste because there wasn't enough to either build adhesion to the crevice walls or enough paste to provide the flex. Here's my planned material - I can trim the added material per recommendation. The paste is cosmetic - you will need additional ABS backing behind the entire patch or it would fail spectacularly. That said, smaller gaps will be less noticeable but in my experience anything thinner than a couple of mm makes it hard to get the paste in the gaps. 1 Quote
gmrhodes13[Staff] Posted February 24, 2020 Report Posted February 24, 2020 I've added tape behind gaps before which stops the paste leaking through. I would however once you have applied to the front and it has dried to add more to the back for extra strength. Quote
fishgoh0nk[TK] Posted February 24, 2020 Report Posted February 24, 2020 (edited) 2 hours ago, Harbinger said: The paste is cosmetic - you will need additional ABS backing behind the entire patch or it would fail spectacularly. That said, smaller gaps will be less noticeable but in my experience anything thinner than a couple of mm makes it hard to get the paste in the gaps. 13 minutes ago, gmrhodes13 said: I've added tape behind gaps before which stops the paste leaking through. I would however once you have applied to the front and it has dried to add more to the back for extra strength. Way ahead of you guys I just didn't want to post the ugly No Parking sign I used as a backer... This was last night. Edited February 24, 2020 by fishgoh0nk 2 Quote
gmrhodes13[Staff] Posted February 24, 2020 Report Posted February 24, 2020 6 minutes ago, fishgoh0nk said: Way ahead of you guys I just didn't want to post the ugly No Parking sign I used as a backer... This was last night. Just be careful leaving any paint on, it can bleed into the plastic and abs paste 1 Quote
justjoseph63[Staff] Posted February 25, 2020 Report Posted February 25, 2020 12 hours ago, fishgoh0nk said: Way ahead of you guys I just didn't want to post the ugly No Parking sign I used as a backer... This was last night. Before using the ABS paste I would go ahead and add your mobility cuts. The reason being is that if you patch the seams first, the pressure from making the cuts afterward may crack the pasted areas (blue arrows). 1 Quote
fishgoh0nk[TK] Posted February 27, 2020 Report Posted February 27, 2020 (edited) On 2/25/2020 at 4:23 AM, justjoseph63 said: Before using the ABS paste I would go ahead and add your mobility cuts. The reason being is that if you patch the seams first, the pressure from making the cuts afterward may crack the pasted areas (blue arrows). @justjoseph63 sorry, off topic. but any tips for making mobility cuts? i'm assuming the thigh cuts should be similar width to the calves? Or as much as you need when bending the leg? Edited February 27, 2020 by fishgoh0nk Quote
gmrhodes13[Staff] Posted February 27, 2020 Report Posted February 27, 2020 2 hours ago, fishgoh0nk said: @justjoseph63 sorry, off topic. but any tips for making mobility cuts? i'm assuming the thigh cuts should be similar width to the calves? Or as much as you need when bending the leg? Screen reference: When in doubt check the gallery section Quote
justjoseph63[Staff] Posted February 28, 2020 Report Posted February 28, 2020 17 hours ago, fishgoh0nk said: @justjoseph63 i'm assuming the thigh cuts should be similar width to the calves? Or as much as you need when bending the leg? I would just remove as much as you need to for comfort. There is no hard and fast rule, but for Centurion level just be sure not to cut off anything past the raised ridge on either the calves or thighs, 1 Quote
fishgoh0nk[TK] Posted February 29, 2020 Report Posted February 29, 2020 (edited) Looks like 1200 grit + novus isn't enough to get the same sheen as the ABS - I bought some 2, 3, and 4000 grit paper, that should do it right? Edited February 29, 2020 by fishgoh0nk wrong topic Quote
justjoseph63[Staff] Posted February 29, 2020 Report Posted February 29, 2020 That should do it, but some polish may be needed as well. 1 Quote
fishgoh0nk[TK] Posted March 15, 2020 Report Posted March 15, 2020 (edited) So I got ABS pasting my thigh seams, but I think I should've gone the thinner seam route - I didn't know how bubbly ABS paste could be - I think I have a density problem - the shade of ABS on some of the areas seem a bit darker - would it be better to paint at this point? I thought polishing might help it, but not really Edited March 15, 2020 by fishgoh0nk typo 2 Quote
darthcue[TK] Posted May 6, 2020 Report Posted May 6, 2020 Can i use lacquer thinner to make ABS paste? Sent from my LYA-L29 using Tapatalk Quote
justjoseph63[Staff] Posted May 6, 2020 Report Posted May 6, 2020 3 minutes ago, darthcue said: Can i use lacquer thinner to make ABS paste? I would not suggest trying it. Acetone is your best bet, but it needs to be the pure type (like you find in a paint or hardware store). Nail polish remover also has acetone, but it is not strong enough to melt ABS. Quote
darthcue[TK] Posted May 6, 2020 Report Posted May 6, 2020 I would not suggest trying it. Acetone is your best bet, but it needs to be the pure type (like you find in a paint or hardware store). Nail polish remover also has acetone, but it is not strong enough to melt ABS.Problem here in my country is pure Acetone is ban because is being use to make METH... Sent from my LYA-L29 using Tapatalk Quote
justjoseph63[Staff] Posted May 6, 2020 Report Posted May 6, 2020 Yikes. I would suggest posting something up on your Garrison boards explaining what you need, as there may be someone who has some they can supply you with. (Acetone, not meth, lol). Are you looking to make it to fill the gap in the lower ridge of your thigh? If so, the gap is not that wide and you can use white E-6000. Just tape up all the edges carefully (remember, it's runny) and don't over-fill the space. 1 Quote
Triple D[TK] Posted May 6, 2020 Report Posted May 6, 2020 Awesome tutorial. Thanks Joseph!!!! 1 Quote
darthcue[TK] Posted May 6, 2020 Report Posted May 6, 2020 Yikes. I would suggest posting something up on your Garrison boards explaining what you need, as there may be someone who has some they can supply you with. (Acetone, not meth, lol). Are you looking to make it to fill the gap in the lower ridge of your thigh? If so, the gap is not that wide and you can use white E-6000. Just tape up all the edges carefully (remember, it's runny) and don't over-fill the space. Thanks bro! I will look for white E6000...Sent from my LYA-L29 using Tapatalk 1 Quote
sskunky Posted May 12, 2020 Report Posted May 12, 2020 Problem here in my country is pure Acetone is ban because is being use to make METH... Sent from my LYA-L29 using TapatalkIf you can find plastic weld which is a liquid solvent cement then you should make it with this. Sent from my iPhone using Tapatalk Quote
Waya Chetan[TK] Posted August 27, 2020 Report Posted August 27, 2020 Appreciate the tutorial. Thank you. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.