Jump to content

Recommended Posts

Posted (edited)

Goodnight


Yes it's correct,

Modify it last Saturday,

The companions warned me of the error

I send the photos with the change

 

Thank you

 

 

IMG_9490.jpg

 

 

 

 

 

IMG_9492.jpg

 

 

 

image.jpg



image.jpg%20%20%20

 

 

 

 

Edited by agm.bobafett
Posted
Hi Antonio, thank you for your EIB application. Let's take a look. 
CRL and EIB Application Requirements:
All the required submission photos have been posted. You armor displays and the required components for L2. Andrew and myself would like to welcome you to the rank of Expert Infantry :salute:. Excellent job :duim:

 

Other-Armor Fit/Assembly:
In this section we review observations made by your fellow troopers and ourselves. Some observations may lead to suggestions to improve the overall look of your armor. If any suggestion affects any application, it will be listed separately in the above or below sections. We have a few areas to go over here so let's get to it. Starting at the top, it looks as if you cut the shoulder covers too short on the back side. There should be a tapering off of the cover where your's appears to be missing. It's recommended you repair or replace these. Take a look at the reference photos below.

Shoulder_1.jpg

 

Reference photos.

gallery_12157_11_941408-crop2.jpggallery_12157_11_941408-crop.jpg

 

There should be minimal gap between the shoulder bells, chest and back plates. We're recommending you tighten the connecting straps and possibly remove more lower return edge allowing the bells to move closer to the chest and back plates.

bell.jpg

 

Reference photo

59603a67dfc5c_Shouldergap.jpg.6f5d750c92d81a87e0e82c789975131b.jpg

 

Chest plate should lay flat against the ab plate. Not a big deal but the chest plate should be positioned closer to the ab. Tightening the straps between the two should remedy this.

chest.jpg

 

Reference photos

a04c7599-b069-4c30-8f60-ca931fd02181.jpgc1cbb2b3-ec19-4c4f-88cc-38ee6732334b.jpg88b875e6-1427-49f6-a693-9f3b16336ed1.jpg

 

Calf closure cover strip placement. As illustrated in the reference photo below the armor halves do not overlap and half the cover strip should be connected to the armor while the other half floats, essentially covering the opposite half of the shin armor.  The arrow represents the edge of the armor in relation to the cover strip. It is recommended the cover strip be moved over. We'll talk about the over lapping armor in the Centurion section.

Reference photo

shin%20non-overlap%202.jpg

 

Centurion Suggestions:
In this section we prepare you for Centurion. If there were any areas of concern they would be discussed here. One area of concern is the helmet decals. The CRL states for level three certification (if applicable): "Tears/traps shall be hand painted or use decals that emulate hand painted (with correct ANH TK details)." Yours will need to be replaced before applying for Centurion.

helmet%20decal.jpg

 

Reference photo/s

f71cceb2-6296-4d8c-895e-549ad1626449.jpgTear%20L.jpgtrap%20L.jpg

 

Drop boxes not alignment with the ammo belt. The CRL states: "For level three certification (if applicable): Drop boxes are vertically aligned with the end of the ammo belt with minimal gap between belt and box." Simply gluing the drop box strap to the cloth belt usually remedy's this issue.

belt.jpgdrop%20box.jpg

 

Reference photo

gallery_12157_59_37792-crop.jpg.940780fd70bce001ae6938f350a32ef3.jpg

 

As mentioned in the EIB suggested section the CRL states: "For level three certification (if applicable): Lower legs must be constructed using the butt joint and cover strip method. Overlap construction is not allowed." This applies to the rear also. The calf halves should butt up against one another with the cover strip over the joint. 

IMG_9492b.jpg

 

Reference photo

gallery_14191_22_57630_1.jpgshin%20non-overlap%202.jpg

 

That's it Antonio. great job on your armor. Hope to see you at Centurion. :jc_doublethumbup:

  • Like 1
  • ukswrath changed the title to TK-12520 Requesting ANH Stunt EIB Status (SDS) [750]
Posted

Congratulations and welcome to the ranks trooper

Posted

Congratulations Antonio! #750 is a easy one to remember! We're 3/4 of the way to 1000 with your approval!

 

Well done!:jc_doublethumbup:

  • Like 1
Posted

Thank you,

 

I will continue working on the armor to reach centurion level.

 

I will take into account all your observations

 

Best regards

  • Like 1
Posted

Congratulations!! :salute:

Posted

Congratulations Antonio, congratulations for your new rank, with a few modifications you will get the centurion level.

 

Welcome trooper

:th_AnimatedBravoSmiley:

  • 4 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...