TK-22019 Requesting ANH Stunt EIB Status[601]

[TK-22019[TK]]

Gary Crowell

TK-22019 Also FISD name

Golden Gate Garrison

 

Armor Maker=Anovos

Helmet Maker=Anovos

Blaster Type=Hyperfirm Elite

 

Height=6ft

Weight=205lbs

Boots Maker=TKBoots

Canvas Belt=TKittell

Hand Plates Type=Plastic

Electronics=Aker/Icomm

Neck Seal Type=Anovos

Holster Maker=Anovos

Edited June 27, 2016 by TK-22019

[illusionz_09[TK]]

Nice job. you may need to add a picture of the front of the cod to show the rivet. Should be an easy approval. Good luck

Edited June 24, 2016 by illusionz_09

[TK-22019[TK]]

Gotcha I can do that

[ukswrath[Staff]]

Hey Gary thanks for your patience we'll be with you shortly

[ukswrath[Staff]]

Hey Gary can you post a picture of the exterior butt to cod plate connection please.

 

Thank you

[TK-22019[TK]]

Will do I'll post it this evening

[TK-22019[TK]]

Exterior pic of butt plate snaps are posted

[ukswrath[Staff]]

Excellent, thank you

[ukswrath[Staff]]

Hey Gary, thanks for your application and welcome to your EI review. It's my pleasure to review another fellow GGG member. Let's get started.

CRL and EIB Application Requirements:

All submission photos have been posted. Your armor displays all the necessary elements to qualify for level 2. Sly and myself would like to welcome to Expert Infantry trooper!   

 

Other-Armor Fit/Assembly:

In this section we review observations  if any, made by your fellow troopers and ourselves. Some observations may lead to suggestions to improve the overall look of your armor. If any suggestion affects any application, it will be listed separately in the above or below sections. None of these suggestions will effect your EIB status.

 

1) The Hovis screens from Anovos are not exactly screen accurate, and the Vcoder paint outlines are washed out. We've been encouraging applicants to replace the screens and clean up the paint lines as best as possible. 

 

 

Here's what the area should look like. Reference picture

 

 

2) The gap at the top of the bells can be tightened by 1/2" allowing the alignment to look better. It's not a huge issue but the tighter the better 

 

 

 

Reference picture

 

3. Also not a huge deal but decreasing the gap between the right bicep and forearm would balance both sides out.

 

 

 

Centurion Suggestions:

Because Centurion photos show much more detail than EIB, items pertaining to Centurion might be seen there and not here. We try to point out all we can from what is seen but the final accuracy is the responsibility of the trooper. This is also where we try and get you in the best possible position for a successful Centurion application.

 

1) The CRL states there can only be one seal between the kidney and ab. Using some ABS paste and paint this can be easily updated to look like one seam. 

 

For level three certification (if applicable):

• A single visible seam line is present.
  

 

 

Reference picture

 

 

2) There is to be minimal gap between the back and kidney. This could be a simple picture issue or you may need to tighten the back to kidney straps.

 

 

Reference pic

 

Great job on your build. Great to have another GGG brother in the EIB ranks.  

[illusionz_09[TK]]

Congrats trooper!

[TK-22019[TK]]

Thank you for the approval. Looks like I'll be busy working on the suggested fixes. Looking forward to someday trooping with you

[Superbee[TK]]

Congratulations trooper !

[ukswrath[Staff]]

Thank you for the approval. Looks like I'll be busy working on the suggested fixes. Looking forward to someday trooping with you

 

Shall do brother 

[Sly11[Admin]]

Congrats Gary!!

 

 

Sent from my iPad using Tapatalk