virimpact Posted May 9, 2016 Report Posted May 9, 2016 (edited) Albert Sanchez F1SD: virimpact Sent from my iPhone using Tapatalk Edited May 9, 2016 by virimpact Quote
ukswrath[Staff] Posted May 9, 2016 Author Report Posted May 9, 2016 Looks like my Brown (rj45 female) was the positive voltage & Blue (rj45 female) was my negative....opposite of the schematic. It was driving me crazy but figured it out!!! All voltage outputs good.....will continue tomorrow on the Amp 2 & Hearing Aid regulator mods!! So proud of myself, 1st time putting together something like this and thanks to your tutorials I was able to make this happen!!!! Thank you!!!! Hey Albert thanks for the feedback. I'll double check my circuitry also to see if there's a discrepancy. Quote
Airborne Trooper[501st] Posted May 9, 2016 Report Posted May 9, 2016 If your twisted pairs are terminated differently then the color will be different than the schematics. IEEE standards with the clip facing down and looking above is White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown. Quote
ukswrath[Staff] Posted May 9, 2016 Author Report Posted May 9, 2016 If your twisted pairs are terminated differently then the color will be different than the schematics. IEEE standards with the clip facing down and looking above is White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown. As long as everyone is using the same product I'm using and the mfg hasn't changed it's design it should be the same you'd think. This is an excellent reminder to check your work. 1 Quote
Machinimax Posted May 10, 2016 Report Posted May 10, 2016 So what do you guys think about this? I'm going to use an iComm as my effects module. I was thinking of modding it so that it would be powered by the XP-5 instead of that little lithium battery. It should be simple enough. I'm thinking just swap the battery out with a 3.6V voltage regulator and then hook it up to the the 5v output of the battery. Any thoughts, suggestions, or concerns? Quote
ukswrath[Staff] Posted May 10, 2016 Author Report Posted May 10, 2016 So what do you guys think about this? I'm going to use an iComm as my effects module. I was thinking of modding it so that it would be powered by the XP-5 instead of that little lithium battery. It should be simple enough. I'm thinking just swap the battery out with a 3.6V voltage regulator and then hook it up to the the 5v output of the battery. Any thoughts, suggestions, or concerns? Shouldn't be a problem. Here's a thread where Sly11 modded his and added an external battery. http://www.whitearmor.net/forum/topic/37188-modding-the-icomm-with-an-external-battery/ Quote
Machinimax Posted May 10, 2016 Report Posted May 10, 2016 Yeah I had seen that and that's what gave me the idea. Quote
Machinimax Posted May 10, 2016 Report Posted May 10, 2016 Also a question of curiosity. Is there a reason there aren't any capacitors used with the voltage regulators in these circuits? I thought they were used in conjunction with the regulator to help maintain a steady output voltage. Quote
ukswrath[Staff] Posted May 10, 2016 Author Report Posted May 10, 2016 Also a question of curiosity. Is there a reason there aren't any capacitors used with the voltage regulators in these circuits? I thought they were used in conjunction with the regulator to help maintain a steady output voltage. To be honest I've been using the regs without capacitors for over a year without any issues. I'm assuming the caps already on board the modified boards are sufficient. Quote
Machinimax Posted May 11, 2016 Report Posted May 11, 2016 Gotcha and (hopefully) one last question and then I can stop being a pain lol. <br><br> Why use the 5 volt regulator on the SHA? I thought it used a 9v battery normally. Quote
ukswrath[Staff] Posted May 11, 2016 Author Report Posted May 11, 2016 Gotcha and (hopefully) one last question and then I can stop being a pain lol. <br><br> Why use the 5 volt regulator on the SHA? I thought it used a 9v battery normally. The SHA is originally powered by 3AA batteries (4.5v). Quote
Machinimax Posted May 15, 2016 Report Posted May 15, 2016 (edited) You'll probably have to click a link since I'm posting on a mobile device but I've drawn a (crude) wiring diagram of my own outlining how I<br><br> believe the voltage reg should be hooked up to the SHA. Tony could you confirm this or notice any mistakes? Thanks!<br><br> <a data-ipb='nomediaparse' href='http://i1238.photobucket.com/albums/ff484/Machinimax05/Mobile%20Uploads/image_zpsfqs8n0q4.jpg'>http://i1238.photobucket.com/albums/ff484/Machinimax05/Mobile%20Uploads/image_zpsfqs8n0q4.jpg</a> Edited May 15, 2016 by Machinimax Quote
ukswrath[Staff] Posted May 15, 2016 Author Report Posted May 15, 2016 You'll probably have to click a link since I'm posting on a mobile device but I've drawn a (crude) wiring diagram of my own outlining how I<br><br> believe the voltage reg should be hooked up to the SHA. Tony could you confirm this or notice any mistakes? Thanks!<br><br> <a data-ipb='nomediaparse' href='http://i1238.photobucket.com/albums/ff484/Machinimax05/Mobile%20Uploads/image_zpsfqs8n0q4.jpg'>http://i1238.photobucket.com/albums/ff484/Machinimax05/Mobile%20Uploads/image_zpsfqs8n0q4.jpg</a> That is correct Quote
ukswrath[Staff] Posted May 15, 2016 Author Report Posted May 15, 2016 Keep in mind at this time I have yet to find a solution to powering the SHA with a 5v USB charger or similar. The chargers carry noise that effects the PCB operation causing a screeching. Looking to find something to filter it. Quote
Machinimax Posted May 16, 2016 Report Posted May 16, 2016 Keep in mind at this time I have yet to find a solution to powering the SHA with a 5v USB charger or similar. The chargers carry noise that effects the PCB operation causing a screeching. Looking to find something to filter it. Ahh! Hence why we hook it up to the 12 volt line as opposed to the 5 volt. Gotcha. Quote
ukswrath[Staff] Posted May 16, 2016 Author Report Posted May 16, 2016 Ahh! Hence why we hook it up to the 12 volt line as opposed to the 5 volt. Gotcha. exactly. There's a company that sells a inline noise filter/suppressor for $50. Haven't tried it yet being I can't justify spending that kind of money on a 1" adapter with no guarantee of working. Quote
Machinimax Posted May 16, 2016 Report Posted May 16, 2016 (edited) exactly. There's a company that sells a inline noise filter/suppressor for $50. Haven't tried it yet being I can't justify spending that kind of money on a 1" adapter with no guarantee of working. Yeah I think I'll stick with the regulator for now. Thanks again for your help! I started working on my circuit yesterday and everything is going very well! Edited May 16, 2016 by Machinimax 1 Quote
virimpact Posted May 16, 2016 Report Posted May 16, 2016 Keep in mind at this time I have yet to find a solution to powering the SHA with a 5v USB charger or similar. The chargers carry noise that effects the PCB operation causing a screeching. Looking to find something to filter it. Think I found the solution to power the SHA, Tony..... http://youtu.be/Bv2vT665bGI Quote
ukswrath[Staff] Posted May 16, 2016 Author Report Posted May 16, 2016 Think I found the solution to power the SHA, Tony..... ah hahaha awesome, and you'll have a nice lemon scent, it's a win win, well... except for the fire part Very cool thanks for sharing. 1 Quote
MoSc0ut[TK] Posted May 16, 2016 Report Posted May 16, 2016 Great, now everyone is going to want a lemon to shove in their buckets, just like all your awesome electronics! Do they make a bracket for that lemon? Jim 1 Quote
ukswrath[Staff] Posted May 16, 2016 Author Report Posted May 16, 2016 Great, now everyone is going to want a lemon to shove in their buckets, just like all your awesome electronics! Do they make a bracket for that lemon? Jim working on it 1 Quote
virimpact Posted May 16, 2016 Report Posted May 16, 2016 Great, now everyone is going to want a lemon to shove in their buckets, just like all your awesome electronics! Do they make a bracket for that lemon? Jim LOL.....im sure someone will 3D print a bracket!!! 1 Quote
virimpact Posted May 16, 2016 Report Posted May 16, 2016 working on it There you go!!!! Tony, never disappoints!!!!! LOL!!!!! 1 Quote
ukswrath[Staff] Posted May 16, 2016 Author Report Posted May 16, 2016 Yeah I think I'll stick with the regulator for now. Thanks again for your help! I started working on my circuit yesterday and everything is going very well! Awesome, exciting to see someone else do this. Very cool Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.