ukswrath[Staff] Posted September 21, 2017 Author Report Posted September 21, 2017 Oh okay I see. I think both front cover strips for the thighs and calves needed to be 20mm? And then fro both backs I was gonna do 25mm. Is this correct? Sorry, back of the thighsSent from my SM-G955U using Tapatalk Quote
darthanael Posted September 21, 2017 Report Posted September 21, 2017 Backhoe the thigh cover strips are 20mm also. Only the calves have 25mmSent from my SM-G955U using Tapatalk Ah okay. So thigh front: 20mm. Thigh back: 20mm. Calves front 20mm. Calves back: 25mm. Sent from my iPhone using Tapatalk Quote
BDWC[TK] Posted September 22, 2017 Report Posted September 22, 2017 On 9/1/2017 at 9:20 PM, ukswrath said: Well you can re-glue them or add the Centurion level straps and see how they sit. Another option if you're afraid to damaged them just add some white velcro to hold them in place. ...or maybe hot bath the tabs on either chest or back? I (and others) definitely has to round out the sharp curves of the Anovos back plate tabs just something to look at, especially if you are tall 1 Quote
BDWC[TK] Posted September 24, 2017 Report Posted September 24, 2017 (edited) Good luck trooper!!! Edited September 24, 2017 by BDWC wrong thread Quote
fxdl2002[501st] Posted September 27, 2017 Report Posted September 27, 2017 Help. I measured the biceps, fitted the plastic. And after gluing they barely fit. I need to remove the armpit six strip an reglue wider. How do I remove e6000 .... Help. PS. I bought abs if I need to just cut a new strip. Quote
ukswrath[Staff] Posted September 27, 2017 Author Report Posted September 27, 2017 Sorry for the delay. Before tearing apart the armor have you removed all the return edge in the areas effected? This will increase the gap. If yes then simply take a butter knife and slide it between the cover and armor at one end and slide it down separating the two. Sent from my SM-G955U using Tapatalk Quote
darthanael Posted September 28, 2017 Report Posted September 28, 2017 Hey Tony, question for Centurion approval. Does the top-right non-functional male snap on the ab piece need to be the "S" popper snap for Centurion approval or can it be a Line 24 male snap? And I suppose same question for the belt-to-ab snaps. Would appreciate your input, thank you! Quote
ukswrath[Staff] Posted September 28, 2017 Author Report Posted September 28, 2017 Hey Nate line 24 is perfectly acceptable. Quote
darthanael Posted September 28, 2017 Report Posted September 28, 2017 2 hours ago, ukswrath said: Hey Nate line 24 is perfectly acceptable. Perfect thank you Tony! Quote
ukswrath[Staff] Posted September 28, 2017 Author Report Posted September 28, 2017 Anytime brother 1 Quote
fxdl2002[501st] Posted September 29, 2017 Report Posted September 29, 2017 On 9/27/2017 at 7:51 AM, ukswrath said: Sorry for the delay. Before tearing apart the armor have you removed all the return edge in the areas effected? This will increase the gap. If yes then simply take a butter knife and slide it between the cover and armor at one end and slide it down separating the two. Sent from my SM-G955U using Tapatalk Thanks . I bought abs plastic to make shims. I can't flex in it.. At all. Thank you! Quote
RubberSlug[TK] Posted October 15, 2017 Report Posted October 15, 2017 So I'm a bit confused because the new ANOVOS belts no longer come assembled. I'm not sure what fixtures to use to attache the plastic, what measurements to use where, etc. Is there a guide starting with what ANOVOS now supplies? Thanks Quote
ukswrath[Staff] Posted October 15, 2017 Author Report Posted October 15, 2017 25 minutes ago, RubberSlug said: So I'm a bit confused because the new ANOVOS belts no longer come assembled. I'm not sure what fixtures to use to attache the plastic, what measurements to use where, etc. Is there a guide starting with what ANOVOS now supplies? Thanks Hey Charlie do you have a photo of the new belt assembly? Quote
RubberSlug[TK] Posted October 15, 2017 Report Posted October 15, 2017 (edited) Thanks, Tony. Reposting these from the FB group for posterity: Edited October 15, 2017 by RubberSlug Quote
Harbinger[IPM] Posted October 19, 2017 Report Posted October 19, 2017 Came into an Anovos TK kit and looking to build to to Centurion out of the box. What, exactly makes the included belt non-accurate? Width? Out of curiosity. Also if I’m understanding the process correctly I would still want to apply for/receive EIB first before Centurion? Quote
ukswrath[Staff] Posted October 19, 2017 Author Report Posted October 19, 2017 52 minutes ago, cinderbike said: Came into an Anovos TK kit and looking to build to to Centurion out of the box. What, exactly makes the included belt non-accurate? Width? Out of curiosity. Also if I’m understanding the process correctly I would still want to apply for/receive EIB first before Centurion? Hello, the costume as a whole is a mixture of two different types, Hero and Stunt. Out of the box it's 501st approved however, for Stunt EIB the two upper holster screws will need to be remove and the holes plugged. For Centurion the belt itself is too flimsy for accuracy standards. We're either recommending or requiring the belt be replaced to avoid any issues at the higher levels accuracy. Quote
Harbinger[IPM] Posted October 19, 2017 Report Posted October 19, 2017 Thanks! I’m sure I’ll have more questions as I get further in the build. Quote
Harbinger[IPM] Posted October 19, 2017 Report Posted October 19, 2017 Is there a source for the 'correct' mic tip mesh material? Didn't see it in your materials list (I probably skimmed over it). Quote
ukswrath[Staff] Posted October 20, 2017 Author Report Posted October 20, 2017 3 hours ago, cinderbike said: Is there a source for the 'correct' mic tip mesh material? Didn't see it in your materials list (I probably skimmed over it). I don't have the tech specs in front of me (on vaca) but I'll do you one better, here's where you cab buy it. 1 Quote
Harbinger[IPM] Posted October 22, 2017 Report Posted October 22, 2017 Tony, will the dropbox elastic need to be riveted at the back for Centurion or is that just an accuracy suggestion? Quote
ukswrath[Staff] Posted October 23, 2017 Author Report Posted October 23, 2017 Tony, will the dropbox elastic need to be riveted at the back for Centurion or is that just an accuracy suggestion? No. There's no requirement how it's attached at any levelSent from my SM-G955U using Tapatalk Quote
Falc1 Posted October 31, 2017 Report Posted October 31, 2017 (edited) Never mind Sir. I surrender. I need to go back to the drawing board. Do more research. I feel that I am not an ideal size for this armor and will need to make some adjustments to get it to fit. I am 5'7" with a stocky build. and Yup, I need to drop about 8 lbs. Hello again, sorry to be a pain in the butt. I am a little confused by the thigh assembly and all the extra cut lines and trimming. I am guessing this is all for a good fit to your leg? I was really hoping to have this done tonight but not looking good. Thank you for all your help. Edited October 31, 2017 by Falc1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.