gusynet[TK] Posted August 17, 2015 Report Posted August 17, 2015 (edited) NAME: José Gustavo Martín Wijnant 501st Id: TK-24976FISD forum name: gusynet GARRISON: Spanish Garrison 501st STATUS: http://www.501st.com/members/displaymemberdetails.php?userID=18940 Mandatory Information Armor Maker: ATA WORKS 2015 Helmet Maker: ATA WORKS 2014 Blaster Type: E-11 Doopydoo's & DLT-19 ASH TK-17116 Height: 6' 4.4" = 194 cm. Weight: 220 lb = 100 kgs. Boots Maker: Zaldi Canvas Belt: I made this myself Hand Plates: Antillis TK-3716 Nech Seal: I made this myself Holster Maker: I made this myself Full Body Front - Arms at side Back - Arms at side Left - Arm raised Right - Arm raised Right Side Detali - Arm raised Left Side Detail - Arm raised Armor Details Abdomen Details Action Shot Cod and Butt Plate Attachment Interior Strapping Helmet Details Front Side Back Hovi Tip Detail Lens Color (Backlit it required) Blaster Details Blaster - Left Blaster - Right Accessory Details Neck Seal Thermal Detonator - Back Holster Attachment Edited October 4, 2015 by gusynet Quote
Nacho[TK] Posted August 19, 2015 Report Posted August 19, 2015 Great work. Buena suerte. The DTL 19 looks great! 1 Quote
cuacpato Posted August 20, 2015 Report Posted August 20, 2015 Vamos Gusy! que esto ya esta hecho! 1 Quote
gazmosis[501st] Posted August 26, 2015 Report Posted August 26, 2015 Hello Josè!! Thank you for your application to Expert infantry. Let's have a closer look at your armor. CRL and EIB Application Requirements: All required photos have been posted. Your armor contains all the required elements to qualify for EIB. Congratulations and welcome to Expert Infantry!! Other-Armor Fit/Assembly: In this section, we will discuss observations made on your armor. I will specify if any changes or upgrades to your armor would be required. There should be a special costume name like "Muscletrooper" or "Enforcer Trooper". You would be the lead trooper. I want to be on your team!!! As for your armor, you have a wonderful build. You have fit this armor to your larger frame very well and it actually looks balanced. Great job. A couple things I noticed: First, I like to see the drop boxes from the belt around 12 mm thick. Yours look to be a bit thicker than that. Second, your center button plate is trimmed out perfect to the edges of the stage. I like to see these just shy of the stage it is glued to but it looks good. Please see the section below for further comments: Centurion Suggestions: I try to see and point out as much as possible, but the ultimate accuracy of the Centurion armor is up to the trooper. I sure hope to see a Centurion application from you. I do need you to adjust a couple things on your helmet, though. I commend anyone who takes on the task of hand painting the details as you did. In a rare occasion I see a detail that, although handpainted, may stray from the original appearance a bit too much. There are two things I would like you to change. First, the outlines of the trapezoids and tears below the eyes should be the same thin line like you have on your ear rank bar areas.Now, because of the size of the dome, the outlines of the traps look acceptable. However, in the tear areas, the outline is a bit enthusiastic. Compare to the original paint. I promise, if you take your gray paint and thin that outline just by half, you will see how much better you will like it. The next issue are your tube stripes. You did a nice job painting them, however, they are located far too low down the cheek. As you see on the screen used helmet, they need to be placed about a pencil width away from the face on the cheek. I can see you are talented with a paintbrush. I believe these will be easy fixes for you. If you want to make them a bit more even and the overall process go easier, do a screen shot of the templates from this thread:http://www.whitearmor.net/forum/topic/14867-tube-stripe-masking-templates/ I paint mine this way now. I place a large piece of masking tape onto the area to be painted and make sure it is completely smooth. I draw a dark line a pencil width away as my placement guide. I tape the template in place and trace out the stripes with a fine sharpie. I then cut out each stripe carefully with an exacto knife. This is what it looks like before paint: And after: The key is making sure the tape is completely smooth before painting . Lastly, the gap on your left side needs to be completely eliminated in your Centurion photos. Congratulations on your EIB accomplishment. Quote
gmrhodes13[Staff] Posted August 26, 2015 Report Posted August 26, 2015 Congrats and welcome to the ranks trooper 1 Quote
gusynet[TK] Posted August 27, 2015 Author Report Posted August 27, 2015 Thank you very much! Now I'm going for the centurion!! Quote
tigresa[TK] Posted August 27, 2015 Report Posted August 27, 2015 (edited) Congratulationssssssssss!!!!!!! Now for Centurion level!!!!!! Go Go Go Go Go !!! Edited August 27, 2015 by tigresa 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.