cuacpato Posted August 4, 2015 Report Posted August 4, 2015 General Information Name = Jordi Bastida TK ID = 24419 FISD name = Cuacpato Garrison = Spanish Garrison Body Type Height = 183cm Weight = 80k Costume Armor = SDS Helmet = SDS Blaster = Doopy doos Boots = Shop Valencia center Canvas belt = I made this myself Hand Plates = Trooperbay Electronics= no Neck Seal = I made this myself Holster = I made this myself Front - Back - Left - Right - Action Shot Armor Details Shoulder Bride Front Shoulder Bridge Back Abdomen Details Hand Plates Thigh Pack Attachment Knee Plate Drop Box Back Cod and Butt plate attachment Interior strapping Laterals Helmet Details Front Sides Back Hovi Tip Detail Lens Color S-Trim Thermal Detonator Boots Holster Neckseal Belt Blaster Overlapping Samples Ooopss! due to the disassembling some pieces underwent breakage and they have been repaired with patches on the inside. Quote
cuacpato Posted August 4, 2015 Author Report Posted August 4, 2015 I just realized that the cover was left longer. grinding ! Quote
Chills[TK] Posted August 5, 2015 Report Posted August 5, 2015 Hola, Jordi! Pretty nice set of armor you have, there. A few things stood out when looking through your pics. Your coverstrips are a bit long, looks like you could trim them down on pretty much all of your pieces so they don't extend beyond the actual piece. Most notably on your thighs, biceps, and forearms. The other thing I see is the gap between your belt and the drop boxes. There should be little to no gap; and it looks like you could bring them up some. Bueno suerte!! Quote
cuacpato Posted August 12, 2015 Author Report Posted August 12, 2015 hi Chills☺ rectifications done. Thank you! 1 Quote
Chills[TK] Posted August 12, 2015 Report Posted August 12, 2015 (edited) The gap is gone! Nice. Now just make sure the edges of the boxes line up with the edge of the belt. And your cover strips look a lot better. Edited August 12, 2015 by Chills Quote
cuacpato Posted August 12, 2015 Author Report Posted August 12, 2015 The alignment is the belt to the abdomen is not in. As soon as you go into that case Quote
gazmosis[501st] Posted August 12, 2015 Report Posted August 12, 2015 Ok Jordi! Thank you for your application for Centurion!! I appreciate all your hard work so let's get to it! CRL and Centurion Application Requirements: I need a couple things updated with your application. First, I need a picture showing the full back side of both drop boxes Next, the application requires a picture of your thigh pack attachment points on your lower, right thigh. These pictures should be from the side showing the rivets. As for the details on your armor. Thank you for catching that cover strip on your thigh back. I will need you to trim all the return edge out of the wrist openings of the forearms as I have marked here:. When done, they should look like this: Other-Armor Fit/Assembly: I am so sorry you had that break in your armor. It is much appreciated, though, that you did the hard work and provided the pictures to make sure you had butt joints rather than overlapping as commonly seen in SDS armor. Nice work on getting that Doopy upgrade for a blaster!! Those points I mentioned above won;t take any time. Get on that so I can approve your Centurion armor!! Quote
tigresa[TK] Posted August 12, 2015 Report Posted August 12, 2015 Co'mon Jordi!!!! That's nothing for you to repair !!! Venga que ya casi lo tienes !!!!! Quote
cuacpato Posted August 13, 2015 Author Report Posted August 13, 2015 (edited) Buenos dÃas. gracias por el Apoyo y gasmosis tigresa! las Nuevas Imagenes sà Realizan, si Contratar hago lo busque. Tengo muchas ganas de Tener El Nivel Deseado! Edited August 13, 2015 by cuacpato Quote
gazmosis[501st] Posted August 13, 2015 Report Posted August 13, 2015 Thank you, Jordi, for trimming the forearms out and providing the pics. It is most ideal to see BOTH rivets attaching the thigh pack in the upper corner like you have on the one side, but........ Congratulations!! Quote
cuacpato Posted August 13, 2015 Author Report Posted August 13, 2015 thanks!!! gazmosis, faie, Carol, group whatsapp, thanks four you help! Quote
Captain_Wordo[TK] Posted August 13, 2015 Report Posted August 13, 2015 Congrats Jordi and welcome to the centurion rank! Quote
Holnave (evan_loh)[TK] Posted August 14, 2015 Report Posted August 14, 2015 It takes a lot of modding and work (to me at least ) to make an overlapping construction armour type to the ANH style and then even more to bring it up to Centurion standards. Congratulations and well deserved! Quote
Chills[TK] Posted August 14, 2015 Report Posted August 14, 2015 (edited) Awesome, Jordi! Congratulations on achieving Centurion! Edited August 14, 2015 by Chills Quote
Snaps[TK] Posted August 14, 2015 Report Posted August 14, 2015 Congrats and welcome to the centurion ranks! Quote
tigresa[TK] Posted August 14, 2015 Report Posted August 14, 2015 Enhorabuena Jordi !!! Bienvenido a los centuriones !!! Quote
gmrhodes13[Staff] Posted August 14, 2015 Report Posted August 14, 2015 Congrats and welcome to the ranks trooper Quote
justjoseph63[Staff] Posted August 14, 2015 Report Posted August 14, 2015 Congratulations, Jordi, way to go! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.