Jump to content

TK-24419 Requesting ANH Stunt Centurion Status [SDS][180]


cuacpato

Recommended Posts

General Information

  • Name = Jordi Bastida

  • TK ID = 24419

  • FISD name = Cuacpato

  • Garrison = Spanish Garrison


Body Type

  • Height = 183cm

  • Weight = 80k


Costume

  • Armor = SDS

  • Helmet = SDS

  • Blaster = Doopy doos

  • Boots = Shop Valencia center

  • Canvas belt =  I made this myself

  • Hand Plates = Trooperbay

  • Electronics= no

  • Neck Seal = I made this myself

  • Holster =  I made this myself


 

 

Front -

2rohjqx.jpg

 

308krxv.jpg

 

Back -

331q811.jpg

Left -

k17zv5.jpg

 

20ic76.jpg

Right -

1zxqzjo.jpg

11tq63s.jpg

 

Action Shot

33uenf7.jpg

 

 

Armor Details

 

Shoulder Bride Front

 

33axaf7.jpg

 

Shoulder Bridge Back

 

n3argw.jpg

 

Abdomen Details

 

mljuza.jpg

Hand Plates

14u95jr.jpg

 

 

 

Thigh Pack Attachment

 

5pj3py.jpg

2v0bchy.jpg

 

Knee Plate

xbaf0m.jpg

dcpx14.jpg

 

 

Drop Box Back

2vsmgkw.jpg

 

Cod and Butt plate attachment

 

4v1pxf.jpg

1ql6jb.jpg

 

 

Interior strapping

25713iv.jpg

 

Laterals

1zybwd2.jpg

2rmsdy1.jpg

 

 

 

Helmet Details

Front

 

2dvkjkh.jpg

Sides

ay96kz.jpg

8xstw4.jpg

Back

 

rbjdj9.jpg

Hovi Tip Detail

30lyngl.jpg

Lens Color

ymoee.jpg

 

S-Trim

24l7t4l.jpg

 

Thermal Detonator

 

16jmyio.jpg

1z91kj.jpg

 

Boots

 

25f53t3.jpg

 

Holster

 

mv6l4k.jpg

 

Neckseal

 

2zz57vb.jpg

 

Belt

 

30cmveo.jpg

 

Blaster

 

292xoi1.jpg

 

2ytwwzp.jpg

 

eame10.jpg

 

Overlapping Samples

 

2co65ae.jpg

 

2n030k6.jpg

 

oh8s35.jpg

 

Ooopss!

 

2jdntxj.jpg

 

 

due to the disassembling some pieces underwent breakage and they have been repaired with patches on the inside.

Link to comment
Share on other sites

Hola, Jordi!

 

Pretty nice set of armor you have, there. A few things stood out when looking through your pics. Your coverstrips are a bit long, looks like you could trim them down on pretty much all of your pieces so they don't extend beyond the actual piece. Most notably on your thighs, biceps, and forearms.

 

The other thing I see is the gap between your belt and the drop boxes. There should be little to no gap; and it looks like you could bring them up some.

 

Bueno suerte!!

Link to comment
Share on other sites

The gap is gone! Nice. Now just make sure the edges of the boxes line up with the edge of the belt. ;)

 

And your cover strips look a lot better.

Edited by Chills
Link to comment
Share on other sites

Ok Jordi!

Thank you for your application for Centurion!! I appreciate all your hard work so let's get to it!

CRL and Centurion Application Requirements:

I need a couple things updated with your application. First, I need a picture showing the full back side of both drop boxes

Next, the application requires a picture of your thigh pack attachment points on your lower, right thigh. These pictures should be from the side showing the rivets. 

As for the details on your armor. Thank you for catching that cover strip on your thigh back. I will need you to trim all the return edge out of the wrist openings of the forearms as I have marked here:post-12041-0-95200800-1439416516_thumb.jpg. When done, they should look like this:post-12041-0-47919100-1439416526_thumb.jpg

 

Other-Armor Fit/Assembly:

I am so sorry you had that break in your armor. It is much appreciated, though, that you did the hard work and provided the pictures to make sure you had butt joints rather than overlapping as commonly seen in SDS armor.

Nice work on getting that Doopy upgrade for a blaster!! 

 

Those points I mentioned above won;t take any time. Get on that so I can approve your Centurion armor!!

 

Link to comment
Share on other sites

Buenos días. gracias por el Apoyo y gasmosis tigresa! las Nuevas Imagenes sí Realizan, si Contratar hago lo busque. Tengo muchas ganas de Tener El Nivel Deseado!

 

nog2za.jpg

 

ekq6v9.jpg

 

 

 

httpg3.jpg

 

33a9efn.jpg

Edited by cuacpato
Link to comment
Share on other sites

Thank you, Jordi, for trimming the forearms out and providing the pics. It is most ideal to see BOTH rivets attaching the thigh pack in the upper corner like you have on the one side, but........

Congratulations!!

Link to comment
Share on other sites

It takes a lot of modding and work (to me at least :P ) to make an overlapping construction armour type to the ANH style and then even more to bring it up to Centurion standards. Congratulations and well deserved! :D

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...