Jump to content

Recommended Posts

Posted

Name: Todd Weishaar
TK: 22237
Forum Name: Iceman25c
Garrison: Star Garrison
Armor Maker: Troopermaster
Helmet Maker: Troopermaster
Blaster Type: Doopy Doos

Height: 6'3"
Weight: 195 lb
Boots Maker: Imperial Boots
Canvas Belt: TKittell
Hand Plates: sonnenschein
Neckseal Type: Darman
Holster Maker: Darman

 

Full Shots

 

DSC00876.jpg

 

DSC00877.jpg

 

Sides, arms raised

 

DSC00882.jpg

 

DSC00879.jpg

 

Side detail

 

DSC00880.jpg

 

DSC00883.jpg

 

Armor Details

 

Buttons

 

DSC00642.jpg

 

Interior strapping

 

DSC00636.jpg

 

DSC00866.jpg

 

DSC00890.jpg

 

DSC00889.jpg

 

DSC00888.jpg

 

DSC00887.jpg

 

Arm detail

 

DSC00655.jpg

 

Forearms

 

DSC00894.jpg

 

Thigh ammo pack

 

DSC00650.jpg

 

DSC00649.jpg

 

Sniper plate

 

DSC00653.jpg

 

DSC00652.jpg

 

Helmet Detail

 

DSC00627.jpg

 

DSC00632.jpg

 

DSC00630.jpg

 

DSC00897.jpg

 

 

DSC00635.jpg

 

DSC00628.jpg

 

DSC00634.jpg

 

Accessories

 

DSC00891.jpg

 

DSC00892.jpg

 

DSC00893.jpg

 

DSC00895.jpg

 

DSC00871.jpg

 

DSC00624.jpg

 

E-11

 

DSC00620.jpg

 

DSC00619.jpg

 

DSC00621.jpg

 

 

Bucket off

 

DSC00874.jpg

 

Action shot

 

DSC00884.jpg

 

 

Thanks to Steve for the guidance and to Adrian for all his hard work!

Posted

GREAT work, Todd!  I think you should have this nailed...

Posted

look good. You might have the side rivets in the wrong positions though. This thread has some good pics and discussions about it: http://www.whitearmor.net/forum/topic/26886-split-rivet-placement/

Meh. Rivet placements were a bit all over the place. If you look at the pictures I posted in that thread you see they didn't even use the same rivets all the time.

​

​If we're going to nit-pick problems with the applicant's suit, the side rivets are at the bottom of the list of things I could mention. But I'm not going to, because It fits all the requirements for centurion. It's clearly not supposed to be a prop-replica, but more of an accurate looking trooping suit. What you're doing is not helping anybody. It's only lowering peoples self-esteem.

  • Like 1
Posted

What kind of Centurion would I be if I knew I could make my armor better but didn't?

 

Rivets out:

DSC00944.jpg

 

New rivets in, painted and ABS paste applied.  Sanding and polishing in the morning.

 

DSC00945.jpg

 

Thanks to everyone for the feedback!

Posted

nice armor...god luck with the application  :duim:

Posted

Hey Todd! Thank you for your application to Centurion. This has been a very interesting application as a whole and worthy of discussion. Many good points have been brought up here and you, Sir, have done some incredible work. Right up to the end. Let's look!!

CRL and Centurion Application Requirements:

All required photos have been posted and your armor contains all the necessary elements to earn the Centurion badge. Congratulations, Todd!

 

Other-Armor Fit/Assembly:

By this point, there really shouldn't be too much to discuss. however, some very good observations and points have surfaced and are worth reviewing. First, let's go right your side rivets. Although I agree that your lower rivet was installed a little low, with the ensemble together, this isn't something that jumped out at me. That lower most rivet didn't throw the armor out of balance or make it look like something was installed incorrectly.  This is what I consider the perfect side rivet installation:post-12041-0-00257000-1436723763_thumb.jpg    Some other rivet locations that I might consider bringing up are ones that are gathered too close together like this:post-12041-0-56026900-1436723189_thumb.jpg or too far from the seam:post-12041-0-41744400-1436723611_thumb.jpg  

I agree that this is not costume replication, but I do believe there are certain things that, although not listed on the CRL, should be maintained as close to the original costume as possible. Especially when the photo references are there and readily available. If the CRL was updated to list all of these points, it would be a huge and very annoying manuscript. Specifically in Todd's case, I made mention of the thermal detonator attachment hardware. Many troopers encourage the slotted, pan head screws to be used here. Yes, that is accurate, but that is something I have never harped too much on. I mentioned it in Todd's case, not because he originally used rivets, but that I only noted two. DSC00873.jpgWhen we always refer to the 4 commonly seen heregallery_12157_51_33329.jpg Todd made the upgradeDSC00895.jpgWell done! Obviously, his side rivet relocation was amazing. This level of attention and Centurion pride as Todd mentioned is admirable!!DSC00948.jpg Todd also upgraded his rear trap vent lines to closer follow the trapezoid shape and not all be parallel to each other. 

If I was to make on comment about something for future adjustment, it would be to shorten the strap on your right side drop box. 

 

Thank you, good Sir, for all your hard work. You have been saluted. Congratulations!!

Posted

Awesome!  Steve, thank you so much for the guidance along the way. I appreciate all your advice and answers.

Posted (edited)

You did it, Todd!  Fantastic job on the fixes, and welcome to ranks, bro!

Edited by justjoseph63
  • Like 1
Posted

Thank you everyone!  I hope to make the Star Garrison proud.

 

I just saw that I'm #172.  That's cool.  My TK ID is from one of the planes I rented to get my private pilot license, N22237, a Cessna 172.  

 

DSC00490.jpg

  • Like 1
Posted

Huge congrats on a hard job, well completed!

Im headed this way SLOWLY and while i struggle with my sniper plate (APs only weakness) i commend you on one of the tidiest knee plates ive seen. Im jealous!

  • Like 1
  • 2 months later...
Posted

Not sure how I managed to miss your thread, Todd, but belated Congratulations, and welcome to the Centurion ranks!!

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...