Stormy1992 Posted July 1, 2015 Report Posted July 1, 2015 (edited) Kyle Morrow TK33092 Stormy1992 Bloodfin Armor Scootch CAP APPLICATION ANH STUNT. (forgot the title in the title :/ ) Since the last time i got my EIB rank, i redid the face of my bucket, Hand painted all decals, Removed flare from the back of my thighs, brought up the drop boxes, bought flexable hand guards and made my bells closer to the bridges. So here we go! Front Back (UPDATE on the rear) flipped TD and actually stood up straight) Right Left Detail Time! Buttons Butt/Kidney and Kidney Plate Notch Hand Guards: Bendy! Bridges Front Left front right Back Left Back right Attachment Thigh Pack Knee Plate Edge Drop Box Back Cod to Butt Interior Back to Front Attachment Outside Forearms Bucket! Front Right Back Left Green Lens S trim Tips Paint detail Blaster Accessories Neck Seal Thermal Back Holster Attachment Extras Thanks for looking!! Here is a chart from my EIB entry photos compared to my Centurion Entry photos. (EIB - CEN - EIB - CEN) Edited July 3, 2015 by Stormy1992 1 Quote
Tusken RTT Posted July 2, 2015 Report Posted July 2, 2015 Just about there, nice job! You could tighten that gap up between the back and ab piece a bit, and flip your TD plate around. Good luck! Quote
Stormy1992 Posted July 2, 2015 Author Report Posted July 2, 2015 (edited) thank you! you got it! the back plate may be due to my self bending a bit forward.. if you notice my left shoulder was raised for some reason. and woopsies! i thought it was on right. it fell off and i thought i put it on the right way hahaha but if needed i can take another picture for my back side Edited July 2, 2015 by Stormy1992 Quote
gazmosis[501st] Posted July 3, 2015 Report Posted July 3, 2015 I can agree with your reason of why you have a gap. It would be better to have a pic of it in its correct position so there is no gap. The Thermal detonator control panel will need repair before I go on. I will check back periodically. Or PM me when the repair is made. Quote
Stormy1992 Posted July 3, 2015 Author Report Posted July 3, 2015 alright! i have the TD done, ill take a photo of my back side today and shoot it your way and add it to the thread! Quote
ukswrath[Staff] Posted July 3, 2015 Report Posted July 3, 2015 Great job Kyle, so close you can taste it Quote
Stormy1992 Posted July 3, 2015 Author Report Posted July 3, 2015 (edited) Thank you!! Update on rear (also added to thread!) Edited July 3, 2015 by Stormy1992 Quote
gazmosis[501st] Posted July 6, 2015 Report Posted July 6, 2015 Welcome back, Kyle!! It has been quite a while since you earned your EIB but your time has obviously been spent getting ready for the big stage! Let's have a look!!! CRL and Centurion Application Requirements: I had noted a few things in the EIB application. Raising the shoulders to eliminate the gap at the shoulder bridges, the space between the drop boxes and the belt , a Sterling based Blaster, flexible hand plates and the oversized thighs. All of these points have been addressed. In the initial submission, the gap between the back and kidney plates and the upside down thermal detonator control panel jumped out at a few people. You have successfully cured both of these ailments. Along with all the necessary pictures that were posted, your armor contains all necessary elements to earn Centurion!! Congratulations!!! Other-Armor Fit/Assembly: There is rarely too much to mention here because...it's Centurion. If you have arrived here, most everything has been perfected. These suggestions DO NOT affect your application, just making suggestions for future improvements. You have a very thin build. This can be both advantageous and not. One thing your physical build will allow you to do is thin out your armor parts for that slim look. Your thighs have already been thinned out slightly. I think you can easily do the same with your shins. There is quite a bit of room at the top. Keep in mind that that on the leg, the bottom of the thigh and top of the shin are roughly the same size with the shin being a bit smaller. Your armor should reflect this. At some point, I would consider adding a little diameter to your ab buttons. While you have your painting mojo out, hit your blaster with some gloss black on the pistol grip. Congratulations again, Sir. Thank you for your attention to your upgrades and TROOP ON!! Quote
ukswrath[Staff] Posted July 6, 2015 Report Posted July 6, 2015 SWEET! Congrats Kyle, welcome to Centurion! Quote
Captain_Wordo[TK] Posted July 6, 2015 Report Posted July 6, 2015 Congrats, Kyle, and welcome to the centurion ranks! Quote
iceman25c[501st] Posted July 6, 2015 Report Posted July 6, 2015 Congratulations! What type of undersuit do you have? In some of your pictures, it looks like rubber. A very cool look! Quote
Stormy1992 Posted July 6, 2015 Author Report Posted July 6, 2015 thanks everyone! ) happy to be here with all of you!! and its underarmor:) may have been the lighting in the photos to give it the rubber feel Quote
gmrhodes13[Staff] Posted July 6, 2015 Report Posted July 6, 2015 Congrats and welcome to the ranks trooper Quote
Sly11[Admin] Posted July 7, 2015 Report Posted July 7, 2015 Congratulations, and welcome to Centurion rank. Sent from my iPad using Tapatalk Quote
starsaber25[Admin] Posted July 8, 2015 Report Posted July 8, 2015 Congrats Kyle! Awesome looking armor! Quote
captsafe66[Admin] Posted July 9, 2015 Report Posted July 9, 2015 Congrats Kyle!! Your are only the second Centurion in the State of Indiana!! Quote
Stormy1992 Posted July 12, 2015 Author Report Posted July 12, 2015 havent seen a change in the ranks yet with posting. is there something i need to do? thanks! Quote
Captain_Wordo[TK] Posted July 12, 2015 Report Posted July 12, 2015 The "centurion granted" information is missing in your profile, you should contact gazmosis, I'm sure he can fix that. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.