gmrhodes13[Staff] Posted October 6, 2012 Report Posted October 6, 2012 So still waiting for armor and done as much as I can up until now, two blasters made so I thought I would give a T-21 a go. Unlike the E-11's most of the materials for this build I have around the place or I can get for next to nothing. Found lots of info and some templates so hold on here I go. Marking out first, measure twice, cut one Now to start glueing a few pieces together Now to glue a few of the wood pieces, wonder if I have enough clamps, wonder who I could ask LOL Quote
Clamps[TK] Posted October 6, 2012 Report Posted October 6, 2012 ah man, here we go again, another build to be jealous of Good luck with this one Glen! Quote
gmrhodes13[Staff] Posted October 6, 2012 Author Report Posted October 6, 2012 ah man, here we go again, another build to be jealous of Good luck with this one Glen! Naw not much to this one, looks easier than E-11, but will be adding lights and sound. Hope my use of clamps was sufficient LOL Quote
Clamps[TK] Posted October 6, 2012 Report Posted October 6, 2012 Hope my use of clamps was sufficient LOL Clamp usage approved Keep it up! Quote
gmrhodes13[Staff] Posted October 6, 2012 Author Report Posted October 6, 2012 Just a few more pieces done Made some spacers to take up the gap between the tubes and added the tapered section Quote
jnnfr72[TK] Posted October 6, 2012 Report Posted October 6, 2012 Glen, You have awesome skills! Quote
gmrhodes13[Staff] Posted October 7, 2012 Author Report Posted October 7, 2012 On 10/7/2012 at 7:24 AM, jnnfr72 said: Glen, You have awesome skills! Thanks but not much to this one, much easier than an E-11 Found a couple of water fittings, had hexagon heads so had to turn them down on a friends lathe, then used a file to make the knurl effect This was the only ribbed pipe I could find Was 30 mm too narrow so what I did was slice it down the middle, cut some sections out of the off cut then glued and siliconed them in. And this is what I have so far Quote
Clamps[TK] Posted October 7, 2012 Report Posted October 7, 2012 very creative solutions, Cannot wait to see the finished product! Quote
gmrhodes13[Staff] Posted October 9, 2012 Author Report Posted October 9, 2012 Few more bits done, top section all sanded and glued Cut and modified some pipe to make the outer rings, had to enlarge one and reduce another, also found a couple of O rings for some of the finer detailing Used pieces from two coupling to make the front section and taper All the pieces on the pipe, think I will paint them all seperately and assemble later with a dab of silicon to hold them in case I want to change any pieces later. Quote
gmrhodes13[Staff] Posted October 9, 2012 Author Report Posted October 9, 2012 A few details pieces done Using some reticulation dripper pipe for the barrel detailing, easy to bend when heated, then tape it to the barrel to hold it's shape until it cools, gives me time to do the blue wire twist . Quote
gmrhodes13[Staff] Posted October 10, 2012 Author Report Posted October 10, 2012 Now for a little bit of bondo Quote
gmrhodes13[Staff] Posted October 11, 2012 Author Report Posted October 11, 2012 On 10/11/2012 at 9:52 AM, chookaboom said: You are too kind Charles Here is where I am up to at this stage. Next step will be trying to round and taper the wood Quote
FunkyTrigger[TK] Posted October 11, 2012 Report Posted October 11, 2012 Your building and prop making skills are awesome. Quote
gmrhodes13[Staff] Posted October 11, 2012 Author Report Posted October 11, 2012 On 10/11/2012 at 3:04 PM, Ourphil said: Your building and prop making skills are awesome. Thanks Phil Just did a bit of rounding on the butt, drilled the chanels for the oil brush and holder Quote
gmrhodes13[Staff] Posted October 13, 2012 Author Report Posted October 13, 2012 Using the electronics from a $6.00 toy gun. Assembled on the front which is hidden in the pipe, added another speaker and a red hi-bright led Fitting a small micro swith, spring and trigger Found a small push battery light, using the front cover as it will give a nice look inside the pipe instead of just seeing the one led. Even with only one led the beam of light is quite intense. Quote
gmrhodes13[Staff] Posted October 13, 2012 Author Report Posted October 13, 2012 Side pieces glued on, just some final detailing and sanding to go So bit of filling, sanding and now some stain Quote
gmrhodes13[Staff] Posted October 13, 2012 Author Report Posted October 13, 2012 The smell of paint is in the air Quote
gmrhodes13[Staff] Posted October 13, 2012 Author Report Posted October 13, 2012 Hit the primer with some 400 wet and dry sandpaper, now to coat in some silver and black Quote
gmrhodes13[Staff] Posted October 14, 2012 Author Report Posted October 14, 2012 Just love how quick this silver dries, now on with the black Quote
Clamps[TK] Posted October 14, 2012 Report Posted October 14, 2012 Glen, you REALLY need to get that Armour!!! You will be one amazing looking trooper as you have most excellence skills with the tools. Build it for Centurion from the get go, I am sure it will be easy for ya! feel free to ship the B-A-G to me if you get BORED with it! clamps Quote
gmrhodes13[Staff] Posted October 14, 2012 Author Report Posted October 14, 2012 Glen, you REALLY need to get that Armour!!! You will be one amazing looking trooper as you have most excellence skills with the tools. Build it for Centurion from the get go, I am sure it will be easy for ya! feel free to ship the B-A-G to me if you get BORED with it! clamps You are tooooooo kind Clamps. Just trying to whittle away the hours, waiting for armor ahhhhhhr, don't know how others do it LOL. Hopefully I have all the info, and I have a copy of the proposed new requirements to be listed soon, so I should be right aiming for Centurion from the start. Just waiting for that armor is ready to ship email Quote
gmrhodes13[Staff] Posted October 15, 2012 Author Report Posted October 15, 2012 Everything painted, stained, varnished, cleared, now it's just a matter of assembly Not sure about weathering as yet, may leave it in pristine condition for a while, then do some weathing down the track, I can see a sandtrooper armor build in the not too distant future, I have been bitten by the bug LOL. I do have plans and pic's for a DLT-19 so there may be a build coming to you soon Quote
Clamps[TK] Posted October 15, 2012 Report Posted October 15, 2012 oh for Christ's sake , now a DLT-19 ?!?!?! I gotta finda a way to smuggle you into Canada and have you build me some weapons! I cannot wait to see that too! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.